Other equipments and machines in bulk on Qoovee

UL/FM APPROVED FIRE FIGHTING SYSTEMS

Industrial Boosters

SUBMERSIBLE PUMPS FOR DIRTY WATER

PUMPS FOR BOOSTERS AND PRESSURIZATION SYSTEMS

HORIZONTAL AND VERTICAL SHAFT DETACHABLE BODY PUMPS

PUMPS FOR INDUSTRIAL PROCESSES

Axial Suction Centrifugal Pump

Stainless Steel Cylinder Mould for paper machine, including spindles, grids, spokes and spacers, with spokes equally spaced on the main shaft, with wire racks mounted on the spokes, stainless steel spokes mounted at equal intervals between the spokes on the main shaft, replacing part of the spokes The stainless steel support ring is embedded at the outer end of the support bar, and the grid is installed along the outer edge of the support steel ring and the spoke, and is tightly wound with stainless steel wire. The paper machine Cylinder Mould is light in weight, corrosion-resistant and reduces energy consumption. Reduce equipment maintenance cycle. Cylinder Mould Normal Specification diameter: 1000mm, 1250mm, 1500mm, 1800mm, 2000mm, 2500mmCylinder Mould Normal working face range: 1000mm - 5000mm Advantage of Stainless Cylinder Mould : 1: High speed: Balance detection, more than 700 meters 2: Weight is reduced by 30% compared to ordinary cages, reducing energy consumption 3: Each piece of spoke has been accurately measured to avoid the overweight phenomenon of the cage and reduce the friction force of the cage on the blanket and the net reduce manufacturing cost 4: All spokes are U-shaped design to reduce water resistance, the surface is very smooth; the speed can be increased by 15-30 meters compared to common cast iron cages without causing water drop phenomenon 5: The strength is higher than that of the common cage for several times, impact resistance, and the maintenance rate of the cage is reduced 6: High surface roughness, increase the area of filtered water, increase production, improve paper quality 7: Acid and alkali resistant, standard 304 stainless steel 8: Very strong integrity, durable.

Used in paper and pulp industry for breaking waste paper and wet-strength paper. This equipment is fitted with P.S. Vokes rotor, which can strengthen hydraulic cycle and fiber defiberizing and also perform continuous breaking with lower energy consumption. Rotor deviates from the center of trough body and trough body structure is D-shape, which can make the contact between pulp and rotor quicker, with higher frequency.Thereby, on condition of not increasing power and volume, capacity can be increased. Rotor and extraction disc are above the bottom plane of trough body, thus, one low-pressure flow area can form around rotor to gather heavy impurities, thereby the service life of rotor and extraction plate can be extended. Main Technical Parameters： Type HT-25 HT-26 HT-27 HT-28 HT-29 HT-30 HT-31 HT-32 HT-33 HT-34 HT-35 HT-36 HT-37 Volume: m3 15 20 25 30 35 40 45 50 60 70 80 100 130 Consistency: % 3-5 Capacity: t/d 80-120 140-180 180-230 230-280 270-320 300-370 350-400 400-450 480-550 550-630 600-700 750-850 950-1050 Motor: kw 160 185 220 280 315 355 400 450 560 630 710 900 1000.

Centrifugal Pump 1. Fully open, three-blade impeller, large flow channel, strong performance without clogging.2. Wear-resistant linings at the suction and discharge ends of the impeller are used to protect the eddy current casing.3. The new protective cover design makes it easier to disassemble.4. Brand new chassis design, stronger and more convenient for coupling adjustment. Fan Pump 1. The replaceable wear-resistant mouth ring protects the pump body from being worn, and ensures that the fluid flows smoothly to the impeller to improve efficiency;2. The blades of the double-suction impeller are divided radially and arranged in staggered and inclined directions, which have the characteristics of high efficiency and low cavitation margin;3. Heavy-duty horizontally split pump body. The inlet and outlet flanges are located in the lower pump body. The inspection, maintenance and replacement of rotor parts can be carried out without dismantling the piping system and the motor.

Machine parameters: Form carrier - 2 Press / mold closing force - 600 Max. clearance between planes — 210 Front span between posts — 343 Press/mould dimensions — 300х400 Max. press/mould height — 220*160 Number of injectors — 2 Screw diameter — 66 Plastification capacity — 45 Injection volume — 750 Injection pressure — 300 Screw speed — -332 Screw torque — 55 Heating zones — 2 Injector heating — 6.9 Injector motor - 22 Auxiliary equipment engine - 5.5. Weight: 3500 kgSizes: 3175/1670/2670

🔥 We fix prices until the end of the month 📌 There is a discount when calling from the Site -7% 📌 We provide after-sales service 📌 We deliver throughout Russia and the CIS ➖➖➖➖ 📲 Do not waste time looking, you have already found us! ➖➖➖➖ Why us? ✅ Experience since 2011 ✅ Guarantee from 12 months ✅ Goods have quality certificates ✅ Compliance with GOST R, ISO, TR CU declarations ✅ Documentation is provided ✅ Our equipment is used in shipbuilding, aircraft building, RosAtom ➖➖➖➖ ⚡ Intelligent Robot Systems (IRS) ) is the largest supplier of welding equipment and consumables. ⚡ We design, develop and install any robotic systems and equipment for various areas of industrial production at enterprises in Russia and the CIS countries. ⚡ Our staff of high-class engineers has more than 50 people. ⚡ We supply high-tech equipment for production. ➖➖➖➖ 💙In order not to lose our contacts, add the announcement to your favorites. ➖➖➖➖ Product features 👉Holding force from 20kg to 4000kg; 👉Weight from 30 g to 2500 g; 👉Clamp material: galvanized, hardened or stainless steel. ➖➖➖➖ 📲 It's easier to ASK than to think. Call❗ ➖➖➖➖ Other product names: Mechanical clamps, Modular clamps, Pneumatic clamps, Hydraulic clamps

🔥 We fix prices until the end of the month 📌 There is a discount when calling from the Site -7% 📌 We provide after-sales service 📌 We deliver throughout Russia and the CIS ➖➖➖➖ 📲 Do not waste time looking, you have already found us! ➖➖➖➖ Why us? ✅ Experience since 2011 ✅ Guarantee from 12 months ✅ Goods have quality certificates ✅ Compliance with GOST R, ISO, TR CU declarations ✅ Documentation is provided ✅ Our equipment is used in shipbuilding, aircraft building, RosAtom ➖➖➖➖ ⚡ Intelligent Robot Systems (IRS) ) is the largest supplier of welding equipment and consumables. ⚡ We design, develop and install any robotic systems and equipment for various areas of industrial production at enterprises in Russia and the CIS countries. ⚡ Our staff of high-class engineers has more than 50 people. ⚡ We supply high-tech equipment for production. ➖➖➖➖ 💙In order not to lose our contacts, add the announcement to your favorites. ➖➖➖➖ Product characteristics 👉 Dimensions, mm from 1000x1000 to 5000x2000 mm 👉 Material Gray cast iron and Ductile iron according to GOST 👉 Type of clamping slots T-shaped 22H12 according to GOST 1574-91 👉 Slot pitch, mm 250 (individual pitch is possible) 👉 System fastening grooves longitudinal and transverse 👉 Installation method fastening to embedded anchors installed in the foundation / frame slipway.➖➖➖➖ 📲 It's easier to ASK than to think. Call❗ ➖➖➖➖ Other product names: Mounting plate, welding plate, cast iron mounting plate, mounting plate with T-slots, cast-iron mounting plate, T-groove, bench mounting plate, corner mounting plate with T-slots

🔥 We fix prices until the end of the month 📌 There is a discount when calling from the Site -7% 📌 We provide after-sales service 📌 We deliver throughout Russia and the CIS ➖➖➖➖ 📲 Do not waste time looking, you have already found us! ➖➖➖➖ Why us? ✅ Experience since 2011 ✅ Guarantee from 12 months ✅ Goods have quality certificates ✅ Compliance with GOST R, ISO, TR CU declarations ✅ Documentation is provided ✅ Our equipment is used in shipbuilding, aircraft building, RosAtom ➖➖➖➖ ⚡ Intelligent Robot Systems (IRS) ) is the largest supplier of welding equipment and consumables. ⚡ We design, develop and install any robotic systems and equipment for various areas of industrial production at enterprises in Russia and the CIS countries. ⚡ Our staff of high-class engineers has more than 50 people. ⚡ We supply high-tech equipment for production. ➖➖➖➖ 💙In order not to lose our contacts, add the announcement to your favorites. ➖➖➖➖ Product features 👉 Maximum press force - 97 kN 👉 Working area - 650 x 450 mm 👉 Power supply - 380V / 3 phase / 50Hz 👉 Motor power 2.2 kW 👉 Dimensions - 1580 x 1070 x 2140 mm 👉 Weight - 1 150 kg ➖➖➖➖ 📲 It's easier to ASK than to think. Call❗ ➖➖➖➖ Other product names: Hydraulic press, hydraulic machine, press

🔥 We fix prices until the end of the month 📌 There is a discount when calling from the Site -7% 📌 We provide after-sales service 📌 We deliver throughout Russia and the CIS ➖➖➖➖ 📲 Do not waste time looking, you have already found us! ➖➖➖➖ Why us? ✅ Experience since 2011 ✅ Guarantee from 12 months ✅ Goods have quality certificates ✅ Compliance with GOST R, ISO, TR CU declarations ✅ Documentation is provided ✅ Our equipment is used in shipbuilding, aircraft building, RosAtom ➖➖➖➖ ⚡ Intelligent Robot Systems (IRS) ) is the largest supplier of welding equipment and consumables. ⚡ We design, develop and install any robotic systems and equipment for various areas of industrial production at enterprises in Russia and the CIS countries. ⚡ Our staff of high-class engineers has more than 50 people. ⚡ We supply high-tech equipment for production. ➖➖➖➖ 💙In order not to lose our contacts, add the announcement to your favorites. ➖➖➖➖ Product characteristics 👉We make any type of carbide burrs: cylindrical, spherical, spherical, oval, spheroconical, spherical with a pointed end, flame-shaped, conical with an angle of 60 and conical with an angle of 90 degrees, conical with a rounded end, conical with a pointed end , conical in the form of an inverse cone, conical, hyperbolic, elliptical, pear-shaped. 👉Diameters of burrs from 3.0 mm to 30 mm. 👉Carbide burrs are sold in bulk from 50 pieces of any type. ➖➖➖➖ 📲 It's easier to ASK than to think. Call❗ ➖➖➖➖ Other product names: Burs, carbide bur, burr, carbide burr, cutter, metal burrs

🔥 We fix prices until the end of the month 📌 There is a discount when calling from the Site -7% 📌 We provide after-sales service 📌 We deliver throughout Russia and the CIS ➖➖➖➖ 📲 Do not waste time looking, you have already found us! ➖➖➖➖ Why us? ✅ Experience since 2011 ✅ Guarantee from 12 months ✅ Goods have quality certificates ✅ Compliance with GOST R, ISO, TR CU declarations ✅ Documentation is provided ✅ Our equipment is used in shipbuilding, aircraft building, RosAtom ➖➖➖➖ ) is the largest supplier of welding equipment and consumables. ⚡ We design, develop and install any robotic systems and equipment for various areas of industrial production at enterprises in Russia and the CIS countries. ⚡ Our staff of high-class engineers has more than 50 people. ⚡ We supply high-tech equipment for production. ➖➖➖➖ 💙In order not to lose our contacts, add the announcement to your favorites. ➖➖➖➖ Product characteristics 👉 Welding method: capacitor and arc. 👉 Fastener material: copper-plated steel, stainless steel, aluminum and brass. 👉 Condensate welding time 1-3 ms. 👉 Power supply 220 V and 380 V 👉 Protection class IP21 ➖➖➖➖ 📲 Easier to ASK than to think. Call❗ ➖➖➖➖ Other product names: Aluminum welding machine, welding machine, welding machine, welding, welder, metal welding, aluminum welding, metal welding, stainless steel welding machine, stud welding machine, stud welding , welding stud

🔥 We fix prices until the end of the month 📌 There is a discount when calling from the Site -7% 📌 We provide after-sales service 📌 We deliver throughout Russia and the CIS ➖➖➖➖ 📲 Do not waste time looking, you have already found us! ➖➖➖➖ Why us? ✅ Experience since 2011 ✅ Guarantee from 12 months ✅ Goods have quality certificates ✅ Compliance with GOST R, ISO, TR CU declarations ✅ Documentation is provided ✅ Our equipment is used in shipbuilding, aircraft building, RosAtom ➖➖➖➖ ⚡ Intelligent Robot Systems (IRS) ) is the largest supplier of welding equipment and consumables. ⚡ We design, develop and install any robotic systems and equipment for various areas of industrial production at enterprises in Russia and the CIS countries. ⚡ Our staff of high-class engineers has more than 50 people. ⚡ We supply high-tech equipment for production. ➖➖➖➖ 💙In order not to lose our contacts, add the announcement to your favorites. ➖➖➖➖ Product characteristics 👉 High-strength brass gearbox housing CW617N 👉 Inlet thread. / out. according to Russian standards 👉 Inlet pressure. 230 bar 👉 Neoprene diaphragm, diameter 50 mm 👉 Seat seal Teflon (PTFE) 👉 Filter bronze, 50 µm 👉 Temperature range from -25°С to +60°С 👉 Gauges 63 mm diameter, accuracy class 2.5, ISO 5171 👉 Weight 1 ,7 kg 👉 Aluminum lacquer coating ➖➖➖➖ 📲 It's easier to ASK than to think. Call❗ ➖➖➖➖ Other product names: Oxygen reducer, Oxygen reducer, Propane reducer, Propane reducer, Propane reducer, Carbon dioxide reducer

🔥 We fix prices until the end of the month 📌 There is a discount when calling from the site -7% 📌 We provide after-sales service 📌 We deliver throughout Russia and the CIS ➖➖➖➖ 📲 Do not waste time looking, you have already found us! ➖➖➖➖ Why us? ✅ Experience since 2011 ✅ Guarantee from 12 months ✅ Goods have quality certificates ✅ Compliance with GOST R, ISO, TR CU declarations ✅ Documentation is provided ✅ Our equipment is used in shipbuilding, aircraft building, RosAtom ➖➖➖➖ ⚡ Intelligent Robot Systems (IRS) ) is the largest supplier of welding equipment and consumables. ⚡ We design, develop and install any robotic systems and equipment for various areas of industrial production at enterprises in Russia and the CIS countries. ⚡ Our staff of high-class engineers has more than 50 people. ⚡ We supply high-tech equipment for production. ➖➖➖➖ 💙In order not to lose our contacts, add an ad to your favorites. ➖➖➖➖ Product features 👉 Pyramidal 👉 With manual and hydraulic pressure roll positioning 👉 CNC and non-CNC 👉 Asymmetric 👉 with 2 and 3 drive rollers Distinctive features: 👉 Robust FE 430B structural steel frame. 👉 Guide rail design with pressure roll deflection protection system using Z-block (patented). 👉 High strength 38NiCrMo4 alloy steel rolls, heat treated and ground to precise tolerances. 👉 Gears made of special 38NiCrMo4 alloy steel with precision ground teeth. 👉 Working position: vertical and horizontal ➖➖➖➖ 📲 It's easier to ASK than to think. Call❗

Crypto Mining Container Custom Design Mining Farm BTC ETH LTC

2015 Yamaha F75 75 hp 4-Stroke 20" Outboard Boat Motor Engine PTT Nice Shape

4 stroke outboard motor 3.5H what=====app ========= +49     152    120     960  85

2014 200HP 200 HP YAMAHA FOUR STROKE OUTBOARD MOTOR F200

Neutral equipment from the manufacturer. Shortest delivery times. Quality stainless steel AISI304

Mobile fire extinguishing systems. The RAF-100P manual fire extinguisher extinguishes fires of classes A (subclass A2), B, C, E (solid combustible materials, liquids, gaseous substances and electrical equipment under a voltage of 40 kV). The extinguishing agent is 100% dielectric, does not harm the electrical parts of the equipment. Maintenance-free. Launch: grating Protected volume: 4 m3 Guaranteed service life: 10 years Dimensions (length, diameter): 210 x 35 mm Maximum weight: 0.185 kg Temperature range: from -50°C to +60°

Autonomous fire extinguishing installations. Autonomous system FR-150 (FR-150) Scope: Production and warehouses; Engine compartments of civil special equipment; Server and data centers; Electrical and cable compartments; Painting booths, and other premises of public and industrial buildings. Start: thermal, autonomously Protected volume: 6 m3 Guaranteed service life: 10 years Dimensions (length, diameter): 277 x 32 mm Maximum weight: 0.295 kg Temperature range: from -60 °C to +60 °C Fire extinguishing aerosol generator FR-150 is used when building automatic fire protection systems as an element that generates a fire extinguishing agent. Extinguishes fire classes A2, B, C, E (solid combustible materials, liquids, gaseous substances and electrical equipment under voltage up to 40 kV) in conditionally sealed rooms. Autonomous systems are launched autonomously using a thermal cord that reacts to a flame and starts a generator with a fire extinguishing aerosol. The extinguishing agent is 100% dielectric, does not harm the electrical parts of the equipment. Does not require maintenance Delivery set: fire-extinguishing aerosol generator, thermal cord with a sensitive element 50 cm long, fastening elements, product passport, warranty card, certificate.

Autonomous fire extinguishing installations. Autonomous system FR-100 (FR-100) Scope: Production and warehouses; Engine compartments of civil special equipment; Server and data centers; Electrical and cable compartments; Painting booths, and other premises of public and industrial buildings. Start: thermal, autonomously Protected volume: 4 m3 Guaranteed service life: 10 years Dimensions (length, diameter): 210 x 32 mm Maximum weight: 0.21 kg Temperature range: from -60 °C to +60 °C Fire extinguishing aerosol generator FR- 100 is used in the construction of automatic fire protection systems as an element that generates a fire extinguishing agent. Extinguishes fire classes A2, B, C, E (solid combustible materials, liquids, gaseous substances and electrical equipment under voltage up to 40 kV) in conditionally sealed rooms. Autonomous systems are launched autonomously using a thermal cord that reacts to a flame and starts a generator with a fire extinguishing aerosol. The extinguishing agent is 100% dielectric, does not harm the electrical parts of the equipment. Does not require maintenance Scope of delivery: fire extinguishing aerosol generator, thermal cord with a sensitive element 50 cm long, fastening elements, product passport, warranty card, certificate.

Autonomous fire extinguishing installations. Autonomous system FR-50 (FR-50) Scope of application: Production and warehouses; Engine compartments of civil special equipment; Server and data centers; Switchboard and cable compartments; Paint booths, and other premises of public and industrial buildings.   Launch: thermal, autonomous Protected volume: 2 m3 Guaranteed service life: 10 years Dimensions (length, diameter):  153 x 32 mm Maximum weight: 0.134 kg Temperature range: from -60 °C to +60 °C   The FR-50 fire extinguishing aerosol generator is used in the construction of automatic fire protection systems as an element that generates a fire extinguishing agent. Extinguishes fire classes A2, B, C, E (solid combustible materials, liquids, gaseous substances and electrical equipment under voltage up to 40 kV.) in conditionally sealed rooms. Autonomous systems are launched autonomously using a thermal cord that reacts to a flame and starts a generator with a fire extinguishing aerosol. The extinguishing agent is 100% dielectric, does not harm the electrical parts of the equipment. Maintenance free Scope of delivery: fire-extinguishing aerosol generator, thermal cord with a sensitive element 50 cm long, fastening elements, product passport, warranty card, certificate.

Autonomous fire extinguishing installations. Autonomous system FR-25 (FR-25) Scope of application: Production and warehouses; Engine compartments of civil special equipment; Server and data centers; Switchboard and cable compartments; Paint booths, and other premises of public and industrial buildings.   Launch: thermal, autonomous Protected volume: 1 m3 Guaranteed service life: 10 years Dimensions (length, diameter):  120 x 32 mm Maximum weight: 0.095 kg Temperature range: from -60 °C to +60 °C The FR-25 fire extinguishing aerosol generator is used in the construction of automatic fire protection systems as an element that generates a fire extinguishing agent. Extinguishes fire classes A2, B, C, E (solid combustible materials, liquids, gaseous substances and electrical equipment under voltage up to 40 kV.) in conditionally sealed rooms. Autonomous systems are launched autonomously using a thermal cord that reacts to a flame and starts a generator with a fire extinguishing aerosol. The extinguishing agent is 100% dielectric, does not harm the electrical parts of the equipment. Maintenance free Scope of delivery: fire-extinguishing aerosol generator, thermal cord with a sensitive element 50 cm long, fastening elements, product passport, warranty card, certificate.

Autonomous fire extinguishing installations. Autonomous system FR-10 (FR-10) Scope: Production and warehouses; Engine compartments of civil special equipment; Server and data centers; Electrical and cable compartments; Painting booths, and other premises of public and industrial buildings. Start: thermal, autonomously Protected volume: 0.4 m3 Guaranteed service life: 10 years Dimensions (length, diameter): 101 x 32 mm Maximum weight: 0.064 kg Temperature range: from -60 °C to +60 °C Fire extinguishing aerosol generator FR- 5 is used in the construction of automatic fire protection systems as an element that generates a fire extinguishing agent. Extinguishes fire classes A2, B, C, E (solid combustible materials, liquids, gaseous substances and electrical equipment under voltage up to 40 kV) in conditionally sealed rooms. Delivery set: fire-extinguishing aerosol generator, thermal cord with a sensitive element 50 cm long, fastening elements, product passport, warranty card, certificate.

Rebar straightening and cutting machine Characteristic Model LM 5/10 LM 6/12 LM 10/14 LM 8/14 Rebar Smooth and cold rolled corrugated rebar 5-10mm 6-12mm 10-14mm 8-14mm rebar) 5-8mm 6-10mm 10-12mm 8-14mm HRB400(hot rolled corrugated rebar) 5-8mm 6-10mm 10-12mm 8-14mm Correct length 1-12m Speed 70m/min 100m/min 130m/min Linearity ≤2mm /m Accuracy ≤±1mm Total power 18.5+4 Kw 22+4 Kw 30+4 Kw 37+4 Kw

Stainless Ice Cream Maker Machine Pre Cooling Soft Serve Ice Cream Machine 36~40L H  Condition of the goods: You will receive full transparency on the individual products, their condition, product prices and informative photos. The goods are in good condition and are visually inspected and classified in category A, B and C.   Minimum purchase: Individual trucks will be made up for you. The price quoted is a truck average price, therefore the price will vary depending on your selection.   Household goods: Consumer Electronics: Computer Appliances: Electric Electrical Cameras, Laptops, Mobile Phones, Drones, Graphics Cards, Motherboards, Video Games, Antminers, Dishwasher, freezer, cookers, fridge/freezer, oven, dryer, washing machine.   Top Brands: Apple,Sony,Panasonic,Heir Thermocool,MSI,Gigabyte,AMD,AEG, Bosch, Bauknecht, LG, Neff, Samsung, Siemens.   Appointment: After making an appointment, you are welcome to visit our warehouse in Nuremberg at any time and convince yourself of our high quality.   Contact: For further details, please send us your contact details as a message, or contact us by phone. We look forward to a successful cooperation. OHIO, USA

Genuine CW-5000DG Industrial Water Chiller Cooling Water 80W 100W CO2 Engraving Cutting Machine  Condition of the goods: You will receive full transparency on the individual products, their condition, product prices and informative photos. The goods are in good condition and are visually inspected and classified in category A, B and C.   Minimum purchase: Individual trucks will be made up for you. The price quoted is a truck average price, therefore the price will vary depending on your selection.   Household goods: Consumer Electronics: Computer Appliances: Electric Electrical Cameras, Laptops, Mobile Phones, Drones, Graphics Cards, Motherboards, Video Games, Antminers, Dishwasher, freezer, cookers, fridge/freezer, oven, dryer, washing machine.   Top Brands: Apple,Sony,Panasonic,Heir Thermocool,MSI,Gigabyte,AMD,AEG, Bosch, Bauknecht, LG, Neff, Samsung, Siemens.   Appointment: After making an appointment, you are welcome to visit our warehouse in Nuremberg at any time and convince yourself of our high quality.   Contact: For further details, please send us your contact details as a message, or contact us by phone. We look forward to a successful cooperation. OHIO, USA

9500 Watt Super Quiet Inverter Generator With CO SECURE Technology  Condition of the goods: You will receive full transparency on the individual products, their condition, product prices and informative photos. The goods are in good condition and are visually inspected and classified in category A, B and C.   Minimum purchase: Individual trucks will be made up for you. The price quoted is a truck average price, therefore the price will vary depending on your selection.   Household goods: Consumer Electronics: Computer Appliances: Electric Electrical Cameras, Laptops, Mobile Phones, Drones, Graphics Cards, Motherboards, Video Games, Antminers, Dishwasher, freezer, cookers, fridge/freezer, oven, dryer, washing machine.   Top Brands: Apple,Sony,Panasonic,Heir Thermocool,MSI,Gigabyte,AMD,AEG, Bosch, Bauknecht, LG, Neff, Samsung, Siemens.   Appointment: After making an appointment, you are welcome to visit our warehouse in Nuremberg at any time and convince yourself of our high quality.   Contact: For further details, please send us your contact details as a message, or contact us by phone. We look forward to a successful cooperation. OHIO, USA

<p11,000 Btu h Self Contained Marine Air conditioner and Heat pump 110-120V 60Hz  Condition of the goods: You will receive full transparency on the individual products, their condition, product prices and informative photos. The goods are in good condition and are visually inspected and classified in category A, B and C.   Minimum purchase: Individual trucks will be made up for you. The price quoted is a truck average price, therefore the price will vary depending on your selection.   Household goods: Consumer Electronics: Computer Appliances: Electric Electrical Cameras, Laptops, Mobile Phones, Drones, Graphics Cards, Motherboards, Video Games, Antminers, Dishwasher, freezer, cookers, fridge/freezer, oven, dryer, washing machine.   Top Brands: Apple,Sony,Panasonic,Heir Thermocool,MSI,Gigabyte,AMD,AEG, Bosch, Bauknecht, LG, Neff, Samsung, Siemens.   Appointment: After making an appointment, you are welcome to visit our warehouse in Nuremberg at any time and convince yourself of our high quality.   Contact: For further details, please send us your contact details as a message, or contact us by phone. We look forward to a successful cooperation. OHIO, USA

Founded in 2016, CDI company mainly focus on providing the maintenance equipment, spare parts and technical service for global Steel, Cement, Oil&Gas;, Smelting&Refinery; and Power Plants. Main Products: Industrial Fan/Blower, Motor, Pump, Valve, Gear Reducer, Crusher, Screen, Feeder, Ball Mill, Conveyor Equipt, Rotary Kiln, Blasting Furnace and spare parts etc.

Painting and drying chamber with a heat-ventilation unit with a capacity of up to 24,000 m³ of air per hour and an economical Riello diesel burner with a thermal capacity of up to 260,000 kcal/hour. The chamber fully meets the requirements prevailing on the market and allows servicing cars of any class. The delivery set includes a heat-ventilation unit with 1 supply and 1 exhaust centrifugal turbofan; - stainless steel heat exchanger; - three-leaf entrance gates 3000x2600 mm; - door for staff 800x2000 mm; - diesel burner; - metal base H=300 mm; - floors with 2 rows of slats or a fully slatted floor, load-bearing capacity 500 kg/wheel; - 2 entrance ramps 2000 mm long; - combined ceiling and side lighting with LED panels; - Remote Control; - a set of air filters. Specifications: Cabin dimensions, mm 6900х4000х2650 Dimensions, mm 7000х5306х3400 (external) Air exchange, m³/h 20000 (with differential 820 Pa) Heat output of the burner, kcal/h max. 260000 Max. Temperature during drying, °C max. 80 Fan drive motor power, kW 2x5.5 Max. Power consumption, kW 13 Lighting power, W 864 Power supply, V/Hz 3 f. X 380V/50Hz

Incorporated in the TABER V-5 Stiffness Tester is a bi-directional pendulum weighing system. Providing an accurate and responsive method for measuring small load increments, this system is a critical component for determining material stiffness or resiliency. Nine (9) distinct ranges permit testing of materials that are extremely lightweight and flexible (such as cellophane or thin metallic foils) to items that are very rigid (such as plastics).For test ranges 2 - 9, specimens are mounted on the Taber V-5 Stiffness Tester using a clamping system. Located on the pendulum, the lower faces of the specimen clamp jaws are exactly on the center of rotation. This ensures a constant test length and deflection angle for accurate and repeatable results. Both jaws of the specimen clamp are adjustable, so the test specimen can be positioned precisely in the center regardless of material thickness. Force is applied to the lower end of the specimen by a pair of rollers. The rollers, which are attached to a driving disc located directly behind the pendulum, push against the test specimen and deflect it from its vertical position. The pendulum applies increasing torque to the specimen as it deflects further from its original position. The test point reading occurs when the pendulum mark aligns with the appropriate driving disc mark (7 1/2° or 15°), which points to the stiffness reading on the dial point. The final reading will depend on the range in which the test is being conducted and what scaling factor to use. The instrument outputs the moment load applied to the test specimen in TABER Stiffness Units (g · cm).Note: The right hand roller includes a ratchet stop mechanism that greatly reduces the potential for inter-operator error caused by over or under-tightening. The travel on the right hand assembly automatically stops when the roller contacts the specimen.To allow the testing of materials with different stiffness properties, range weights can be applied to the pendulum. For extremely light weight materials, a compensator range weight is mounted to the top of the pendulum. Range weights of 500, 1000 and 2000 "Taber Units" are mounted to the bottom of the pendulum and required for stiffer materials. An optional range weight set of 3000 and 5000 Taber units is required for test ranges 7, 8 and 9.Range 1 is used with Taber's optional Sensitivity Range Attachment (also referred to as SR or High Sensitivity Attachment) to test extremely lightweight and flexible materials whose Taber Stiffness Unit value are between 0 - 1. Examples include cellophane, natural fibres and synthetic filaments, tissue paper, metallic foils, films, etc. The attachment includes two parts, the Driven Pins Holder which is secured between the clamp jaws, and the Driving Pins Holder which is mounted to the studs in place of the left and right hand rollers. Both parts include precision pins that are oriented horizontal to the face of the V-5 Stiffness Tester. A specimen 1 1/2" x 1 1/2" is mounted such that the second and fourth pins are above the specimen. As the driving disc rotates, the fourth pin of the Driving Pins Holder pushes down on the specimen while the first pin pushes up. As the sample is deflected, the Driven Pins Holder aligns the pendulum to the appropriate stiffness value. For Range 1, the specimen is only deflected to the right.Many customers have also utilized the Taber V-5 Stiffness Tester to evaluate wire and cable stiffness characteristics. The tester now incorporates a "v-notch" in the clamps to accommodate this testing. Suggested samples are 70mm long and 3mm - 8mm in diameter, and centered in the notch with care so as to not pinch or crimp the sample. For wire and cable samples less than 3mm diameter, it is recommended to secure the sample at a location in the flat region of the clamp. Samples with curvature may interfere with proper set-up and function of the Stiffness tester and should be avoided. In addition, test results obtained should be used for comparison only - that is, between lots, between materials, etc.

Incorporated in the TABER V-5 Stiffness Tester is a bi-directional pendulum weighing system. Providing an accurate and responsive method for measuring small load increments, this system is a critical component for determining material stiffness or resiliency. Nine (9) distinct ranges permit testing of materials that are extremely lightweight and flexible (such as cellophane or thin metallic foils) to items that are very rigid (such as plastics).For test ranges 2 - 9, specimens are mounted on the Taber V-5 Stiffness Tester using a clamping system. Located on the pendulum, the lower faces of the specimen clamp jaws are exactly on the center of rotation. This ensures a constant test length and deflection angle for accurate and repeatable results. Both jaws of the specimen clamp are adjustable, so the test specimen can be positioned precisely in the center regardless of material thickness. Force is applied to the lower end of the specimen by a pair of rollers. The rollers, which are attached to a driving disc located directly behind the pendulum, push against the test specimen and deflect it from its vertical position. The pendulum applies increasing torque to the specimen as it deflects further from its original position. The test point reading occurs when the pendulum mark aligns with the appropriate driving disc mark (7 1/2° or 15°), which points to the stiffness reading on the dial point. The final reading will depend on the range in which the test is being conducted and what scaling factor to use. The instrument outputs the moment load applied to the test specimen in TABER Stiffness Units (g · cm).Note: The right hand roller includes a ratchet stop mechanism that greatly reduces the potential for inter-operator error caused by over or under-tightening. The travel on the right hand assembly automatically stops when the roller contacts the specimen.To allow the testing of materials with different stiffness properties, range weights can be applied to the pendulum. For extremely light weight materials, a compensator range weight is mounted to the top of the pendulum. Range weights of 500, 1000 and 2000 "Taber Units" are mounted to the bottom of the pendulum and required for stiffer materials. An optional range weight set of 3000 and 5000 Taber units is required for test ranges 7, 8 and 9.Range 1 is used with Taber's optional Sensitivity Range Attachment (also referred to as SR or High Sensitivity Attachment) to test extremely lightweight and flexible materials whose Taber Stiffness Unit value are between 0 - 1. Examples include cellophane, natural fibres and synthetic filaments, tissue paper, metallic foils, films, etc. The attachment includes two parts, the Driven Pins Holder which is secured between the clamp jaws, and the Driving Pins Holder which is mounted to the studs in place of the left and right hand rollers. Both parts include precision pins that are oriented horizontal to the face of the V-5 Stiffness Tester. A specimen 1 1/2" x 1 1/2" is mounted such that the second and fourth pins are above the specimen. As the driving disc rotates, the fourth pin of the Driving Pins Holder pushes down on the specimen while the first pin pushes up. As the sample is deflected, the Driven Pins Holder aligns the pendulum to the appropriate stiffness value. For Range 1, the specimen is only deflected to the right.Many customers have also utilized the Taber V-5 Stiffness Tester to evaluate wire and cable stiffness characteristics. The tester now incorporates a "v-notch" in the clamps to accommodate this testing. Suggested samples are 70mm long and 3mm - 8mm in diameter, and centered in the notch with care so as to not pinch or crimp the sample. For wire and cable samples less than 3mm diameter, it is recommended to secure the sample at a location in the flat region of the clamp. Samples with curvature may interfere with proper set-up and function of the Stiffness tester and should be avoided. In addition, test results obtained should be used for comparison only - that is, between lots, between materials, etc.

The IQ150 is programmed to display clearly worded prompts which allows operators to not need instructional manuals.The IQ150 measures density and computes density difference, dot area, and dot gain. The densitometer simultaneously displays all the filters densities showing the major filter in large lettering. The IQ150 Densitometer, engineered with the latest in software technology, is so easy to use that an operator's manual isn't even needed! Yet, the affordable IQ150 fulfills your press and pre-press quality control needs with precision. It quickly and easily computes the main densitometric functions: density, density difference, dot area and dot gain. The IQ150 Densitometer has proven itself an indispensable workhorse for printers. No other portable densitometer available today can offer so much, so consistently, at so reasonable a price. Available functions: Density, Density Difference, Dot Area and Dot Gain. Simultaneous display of all filter densities: Shows the major filter value in large characters; the three minor values are shown smaller. Plainly worded, self-guiding prompts: Simple directions appear on the display; no complicated operating instructions or training manuals to study. Large, high-contrast display area: Easy-to-read display can be viewed from virtually any angle. Murray-Davies and Yule-Nielsen dot area calculations: Switch between equations at the touch of a button. Convenient one-hand operation: All densitometric functions are quickly and easily accessed through one button. Automatic turnoff: Saves battery by shutting off after 90 seconds of non-use. Several thousand readings per battery charge: Also runs from the A.C. adapter/charger. RS-232 output port: Use with a printer for reports, or a computer for analysis or data storage. Selectable manual or automatic transfer. Easy software calibration: Eliminates trial-and-error screwdriver adjustments. Available in French or Spanish: Displays all user prompts in the selected language.

The TBX1000C insures consistent process control in the manufacturing of films, laminates, and substrates. It measures density and density difference of either color or black and white substrates. Single-Step measurement of Color, UV, or IR Transmission Optical DensityThe TBX1000C(tm) Color Transmission Densitometer insures consistent process control in the manufacture of films, laminates, and substrates. The TBX1000C, with Status A (Status M on request), measures density and density difference of either color or black & white substrate with a great degree of accuracy and precision. Status A is used for reading positives, such as transparencies and prints. Status M for reading negatives. The unit has the capability of reading up to three color filters, plus visual. Custom filter set, including for measuring infrared and ultraviolet, can be used. The different filters are easily selected by rotating the knob at the end of the probe. The unit has both an absolute mode and a relative mode, which can be used for comparing the measured values to a previously stored value for consistent process control. Transmission Densitometer/Opacity Meter measures and calculates percent opacity, percent transmission, and transmission optical density. There is no more need to figure the percentages manually. The unit has been designed for user convenience and error-free measurement. The data can be uploaded to a spreadsheet via the USB port using an optional data transfer program (p/n A2128). Measures density and density difference Use for color or black & white substrates Soft key menu operation 7.5 inch throat to measure large samples Accurate repeatable readings Software Calibration Switchable LED table lamps Takes RGB readings using Status A filter set Status M and custom filters upon request Easy selectable filters USB port Data capture program available.