Electrical equipment and parts in bulk on Qoovee

1.0 HP Pervane & ccedil; apı 1,270 mm < / span> Motor </ span> 1 hp < / span> 0 Pa hava akışı 36,180 m3 / h 25 Pa hava akışı 31,594 m3 / h 0 Pa spesifik performans 34.5 m3 / wh

Wholesale supply of disinfection lamps for medical and household purposes. Large selection from manufacturers in China. Prices vary in size and capacity. Send a request and our managers will answer all your questions.

12V 225 Ah, Size 48x27x23

12V190Ah, Size 48x22x21

12V 75 Ah, Size 26x17x19

12V 60 Ah, Size 23x17x19

Fixtures LED console series STIK & nbsp; are made in a modern stylish waterproof aluminum case. Complete with corrosion-resistant stainless steel bracket & nbsp; for console installation. As a console you can & nbsp; use & nbsp; separately purchased & nbsp; L-shaped bracket . & nbsp; luminaires with KSS of a wide type - adjustable, provides the ability to change the angle of inclination when installed in the range of 0 ... 30º; with a resolution of 5 & ordm ;. B LEDs from OSRAM and CREE are used as a light source. As a current source - & nbsp; proven and reliable drivers & nbsp; Russian-made with galvanic isolation, & nbsp; active power corrector and protection from 380 V. Specifications Supply voltage & nbsp; 176 ... 264 V, 50 Hz Power factor & nbsp; & gt; 0.95 Class of protection against electrical shock. shock & nbsp; I Color temperature & nbsp; 4000/5000 K Color rendering index, CRI & nbsp; 80 Ripple factor & nbsp; & lt; 1% Bore diameter & nbsp; 50mm Step. protection & nbsp; IP65 Operating temperature & nbsp; - 40 ... + 40 & ordm; C Resource & nbsp; & gt; 50,000 hrs Diffuser & nbsp; Transparent

Complete switchgears are & nbsp; for the reception and distribution of electrical energy with a frequency of 50 Hz with a voltage of 10 (6) kV & nbsp; with rated current of busbars 630,1000,1250,1600,2000,2500 and 3150А and operated in regions with a temperate climate (from -25 ° С to + 40 ° С). & nbsp; Type of climatic modification U3 or T3 according to GOST 15150. & nbsp; Normal operation of the switchgear is ensured under the following conditions: & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; 1. Altitude above sea level & ndash; no more than 1000 m; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; 2.Environment & ndash; is not explosive, does not contain conductive dust, corrosive gases and vapors in concentrations that reduce the parameters of the KTP in unacceptable standards; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; & nbsp; 3.Type of atmosphere & ndash; II in accordance with GOST 15150. & nbsp; The main technical parameters of the switchgear are shown in Table 1. Classification of cabinets is given in Table 2. In case of double-row cabinet design, the switchgear is equipped with busbar bridges. Busbar bridges are only installed on the outermost cabinets. The distance between the fronts of the cabinets must be 2000, 2500 or 3000 mm. & Nbsp;

Saeco Royal Classic Specifications: Pump pressure, Bar: 15 Type espresso machine For home business Grain and ground coffee Functions: auto shut-off, selection of the volume of portions, supply of hot water for tea, heating of cups, adjustment of coffee strength. Manual cappuccino preparation Ground coffee container Capacity for water, l: 2.4 Capacity of the container for coffee beans, g 300 Weight, kg: 13 Boiler material: aluminum alloy Body material: ABS plastic Power consumption, W: 1250 Color: silver with black Dimensions (WxHxD), mm: 340x395x410 Made in Germany The history of the Saeco International Group dates back to the 70s of the last century. In 1976, a company was created that produced equipment for the preparation of espresso coffee. From that moment, the history of a uniquely tasty drink brewed in a coffee machine began. Saeco gives you the perfect opportunity to enjoy all the notes and the enchanting taste of this invigorating drink. The automatic Saeco Royal Classic machine differs from the models offered on the market by its simplicity and compactness in use, it is designed for making espresso coffee. It has a number of advantages, the main of which are additional functions: the quality of coffee grinding is regulated, it is pre-wetted, there is a nozzle for frothing milk and control of the volume and consumption of coffee per serving. In addition, you will be pleased with the spacious waste container for 30 portions and a capacity of 2.4 liters of water. It should be emphasized that the machine is not designed to accept ground coffee, it has a built-in grinder that accepts coffee of any roast. Such features and equipment allow using the coffee machine in small offices, banks and other similar organizations, where the invigorating and magical qualities of coffee will be 100% appreciated. The durability and quality of the Saeco Royal Classic coffee machine is confirmed by the material from which it is made, as evidenced by its appearance. The parts of the machine and the main connecting parts are made of brass and steel, the base is metal, and the body is high temperature ABS plastic. The Saeco Royal Classic is a machine designed for continuous operation, very easy to use and maintain.

WARRANTY AND QUALITY ADDRESS ....

Prefabricated chambers one-way service KSO 306 and busbar bridges SHM and SMR for them are intended for switchgear configuration voltage 6 or 10 kV AC frequency 50 Hz with isolated neutral. Type of climatic modification U3 by GOST15150. Normal operation of KSO is ensured when following conditions: 1. Height above sea level - no more than 1000 m; 2. Environment - non-explosive, not containing conductive dust, corrosive gases and vapors in concentrations that reduce the parameters of the KTP within unacceptable limits; 3. Wind speed up to 36 m / s (wind pressure speed up to 800 Pa); 4. Type of atmosphere - II in accordance with GOST 15150. The main circuits of the KSO consist of the following devices; 1. Autogas load switch VN-RA - chambers 03-06, 08.09 and 24; 2. Disconnector with grounding knives RV - chambers 01, 02, 07, 10, 11, 14P, 14L; 3.Vacuum circuit breaker BB / TEL or VR-1 with electromagnetic drive - 12V, 14V and 17V chambers. A set of protections is provided in the chambers - overcurrent protection, overcurrent cutoff, ground fault protection, voltage circuit monitoring, automatic transfer switch (ATS); 4. Voltage transformers - chambers 10 and 11; 5.Transformers for auxiliary needs - cameras 12V, 13V and 23. On request, active and reactive energy metering cabinets are supplied. With a two-row design, the switchgear is completed bus bridges with or without disconnectors (ШМР). Bus bridges are installed only on the outermost chambers. Distance between the facades of the chambers: 2000 mm (ШМР-1, ШМ-1); 2500 mm (ShMR-2, ShM-2); 3000 mm (ShMR-3, ShM-3); 3500 mm (ShMR-4, ShM-4). Connection of cameras to the external network - cable. The chambers are provided with all interlocks in accordance with regulatory documents. An example of ordering a KSO camera made according to scheme 05, with a rated voltage of 10 kV Chamber KSO 306-05 U3 TU U 31.2-14152239-002: 2006, An example of ordering a KSO chamber with a vacuum circuit breaker, made according to the 13 V circuit, with a nominal voltage of 10 kV Chamber KSO 306-13V U3 TU U 31.2-14152239-002: 2006, Example of ordering a busbar bridge with disconnectors with a distance between the facades of the chambers of 2500 mm Bus bridge SHMR-2 U3 TU U 31.2-14152239-002: 2006.

Panels of switchboards SCHO-06 are designed to receive and distribute electrical energy of three-phase alternating current with a frequency of 50 Hz and voltage up to 660 V and to protect outgoing lines from overloads and short-circuit currents. Type of climatic modification U3 in accordance with GOST 15150. Normal operation of SCHO is provided under the following conditions: 1. Height above sea level - no more than 1000 m; 2. Environment - non-explosive, not containing conductive dust, corrosive gases and vapors in concentrations that reduce the parameters of the KTP within unacceptable limits; 3. Wind speed up to 36 m / s (wind pressure speed up to 800 Pa); 4. Type of atmosphere - II in accordance with GOST 15150. SCHO panels are manufactured in two versions according to the degree of protection (the first digit in the panel designation): 1 - open (degree of protection IP00 and only from the side of the facade - IP20); 2 - closed (degree of protection IP20 and only from the bottom side - IP00). According to the purpose, the panels are divided into introductory, sectional, distribution and auxiliary ones. Accessory panels include supervisory panels, metering cabinets, and end panels. When installing the panels in two rows, the switchgear is equipped with a busbar bridge with a distance between the facades of -1000, 1500 and 2000mm. The panels are equipped with the following equipment: 1. Introductory and sectional - automatic switches of withdrawable and fixed design and circuit breakers, 2. Distribution circuit breakers - withdrawable or fixed circuit breakers, RPS fuse switches or insulated switches with RBK or ARS fuses. On request, the products are completed with installations for reactive power compensation. Panels are assembled into transport groups up to 4 m long. Example of ordering an input panel SCHO of protection degree IP00 with a rated current of inputs 1600 A, made according to scheme 01 ShchO-06-1101 U3 panel TU U 31.2-14152239-004: 2006, Example of ordering a busbar bridge with a distance between the facades of the chambers of 1000 mm Bus bridge SHM-2 U3 TU U 31.2-14152239-004: 2006.

Complete transformer substations for urban networks of through-passage and dead-end type - KTPG with a capacity of 100-2500 kVA, HV voltage of 6 or 10 kV and LV voltage of 0.4 kV are designed to receive, convert and distribute electrical energy of three-phase alternating current with a frequency of 50 Hz in systems with a dead-grounded neutral transformer on the low voltage side. KTPG are designed to supply power to agricultural consumers, individual settlements and small industrial facilities in areas with a temperate climate (from -45 ° C to + 40 ° C). Type of climatic modification U1 in accordance with GOST15150. Normal operation of the KTP is ensured under the following conditions: 1. Height above sea level - no more than 1000 m; 2.Environment - non-explosive, not containing conductive dust, corrosive gases and vapors in concentrations that reduce the parameters of the KTP in unacceptable limits; 3. Wind speed up to 36 m / s (wind pressure speed up to 800 Pa); 4. Type of atmosphere - II in accordance with GOST 15150. High-voltage input - air or cable, outgoing line branches - air or cable. Also, KTPG are manufactured as one-transformer and two-transformer (with sectioning for high and low voltage). Circuit breakers are installed on the LV side. Their number and rated current are shown in the table. The package of delivery of the KTP includes UVN (air inlet) and LVDN cabinets, a power transformer, an outdoor disconnector RLNDz-10/630 (on request). On request, the KTP can provide street lighting lines, which are switched on automatically by a signal from the built-in relay and by installations for reactive power compensation. ... Example of ordering a single-transformer KTP with a power of 630 kVA with a network voltage of 6 kV HV cable gland and LV cable gland KTPG-2K- 630/6 / 0.4 U1 TU U 3.2-14152239-001: 2004. Example of ordering a two-transformer KTP with a capacity of 250 kVA and a network voltage of 10 kV HV air inputs and LV cable glands

Complete transformer substations dead-end - KTP-1 with a capacity of 25 - 630 kVA, HV voltage 6 or 10 kV and LV voltage 0.4 kV are intended for receiving, converting and three-phase electrical power distribution alternating current with a frequency of 50 Hz in systems with solid-grounded neutral of the transformer on low voltage side. KTP-1 are intended for power supply of agricultural, industrial consumers, individual communities points and small industrial facilities in areas with a temperate climate (from -45 ° С to + 40 ° С). KTP-1 is installed on the simplest concrete site. Type of climatic modification U1 in accordance with GOST15150. Normal operation of the KTP is ensured under the following conditions: 1. Altitude above sea level - no more than 1000 m; 2. Environment - non-explosive, not containing conductive dust, corrosive gases and vapors in concentrations that reduce the parameters of the KTP within unacceptable limits; 3. Wind speed up to 36 m / s (wind pressure up to 800 Pa); 4. Type of atmosphere - II in accordance with GOST 15150. High-voltage input - air or cable, outgoing line branches - air or cable. Dead-end KTP-1 are manufactured as one-transformer and two-transformer (with high and low voltage sectioning). Circuit breakers are installed on the LV side. Their number and rated current are shown in the table. The package of delivery of the KTP includes UVN (air inlet) and LVDN cabinets, a power transformer, an outdoor disconnector RLNDz-10/630 (on request). On request, the KTP can provide street lighting lines, which are switched on automatically by a signal from the built-in relay.

Transformer substations complete dead-end - KTP-2 power 25-2500 kVA, voltage HV 6 or 10 kV and LV voltage 0.4 kV intended for reception, transformation and distribution electrical energy three-phase alternating current with a frequency of 50 Hz in systems with grounded neutral transformer on the low side voltage. KTP-2 are intended for power supply of agricultural consumers, individual settlements and small industrial facilities in areas with a temperate climate (from -45 ° C to + 40 ° C). KTP-2 is installed on the simplest concrete site. Type of climatic modification U1 in accordance with GOST15150. Normal operation of the KTP is ensured under the following conditions: 1. Height above sea level - no more than 1000 m; 2. Environment - non-explosive, not containing conductive dust, corrosive gases and vapors in concentrations that reduce the parameters of the KTP within unacceptable limits; 3. Wind speed up to 36 m / s (wind pressure speed up to 800 Pa); 4. Type of atmosphere - II in accordance with GOST 15150. High-voltage input - air or cable, outgoing line branches - air or cable. Passage KTP-2 are manufactured as one-transformer and two-transformer (with sectioning for high and low voltage). Circuit breakers are installed on the LV side. Their number and rated current are shown in the table. The package of delivery of the KTP includes UVN (air inlet) and LVDN cabinets, a power transformer, an outdoor disconnector RLNDz-10/630 (on request). On request, the KTP can provide street lighting lines, switched on automatically by the signal of the built-in relay and by installations for reactive power compensation.

Complete pole transformer substations with a capacity of 25-250 kVA of three-phase alternating current with a frequency of 50 Hz with a voltage of 10 (6) \ 0.4 kV are single-transformer substations of a dead-end type of outdoor installation and are used to supply power to agricultural consumers, individual settlements and small industrial facilities in areas with temperate climate (from -45 ° С to + 40 ° С). Type of climatic modification U1 in accordance with GOST15150. Normal operation of the KTPS is ensured under the following conditions: 1. Altitude above sea level - no more than 1000 m; 2. Environment - non-explosive, not containing conductive dust, corrosive gases and vapors in concentrations that reduce the parameters of the KTP within unacceptable limits; 3. Wind speed up to 36 m / s (wind pressure up to 800 Pa); 4. Type of atmosphere - II in accordance with GOST 15150. KTPS has the following components: 1. Device on the high voltage side (UHV); 2. Transformer of power outdoor installation three-phase or single-phase transformer of OMP-10 or 6kV type; 3. Switchgear on the low voltage side (LVSN) with circuit breakers on outgoing lines and street lighting line.

Complete transformer substations with capacity 25-250 kVA three-phase alternating current with a frequency of 50 Hz voltage 10 (6) \\ 0.4 kV are single-transformer substations of dead-end type outdoor installation and serve for power supply agricultural consumers, individual populations points and small industrial facilities in areas with a temperate climate (from -45 ° С to + 40 ° С). Type of climatic modification U1 in accordance with GOST15150. Normal operation of the KTPM is ensured when following conditions: 1. Altitude above sea level - no more than 1000 m; 2. Environment - non-explosive, not containing conductive dust, corrosive gases and vapors in concentrations that reduce the parameters of the KTP within unacceptable limits; 3. Wind speed up to 36 m / s (wind pressure up to 800 Pa); 4. Type of atmosphere - II in accordance with GOST 15150. KTPM has the following components: 1. Device on the high voltage side (UHV); 2. Transformer of power outdoor installation three-phase or single-phase transformer of OMP-10 or 6kV type; 3. Switchgear on the low voltage side (LVSN) with circuit breakers on outgoing lines and street lighting line.

TM oil transformers are produced with a capacity from 25 to 1000 kVA for a rated voltage of the primary winding of 6 or 10 kV and a rated voltage of the secondary winding of 0.4 or 0.23 kV with a frequency of 50 Hz. Scheme and group of connections of windings U / Un-0 or D / Un-11. Type of climatic modification U1 in accordance with GOST 15150. Normal operation of transformers is ensured under the following conditions: 1. Height above sea level - no more than 1000 m; 2. Environment - non-explosive, not containing conductive dust, corrosive gases and vapors in concentrations that reduce the parameters of the KTP within unacceptable limits; 3. Wind speed up to 36 m / s (wind pressure speed up to 800 Pa); 4. Type of atmosphere - II in accordance with GOST 15150; 5. Ambient temperature - from -45 ° С to + 40 ° С. Voltage regulation is carried out by switching without excitation (PBV) when the transformer is disconnected from the mains, both on the high and low voltage sides. The voltage is regulated from the high voltage side by ± 2x2.5% of the nominal value. Outdoor transformer bushings, removable, porcelain bushing insulators. At currents of 630 and 2500A, contact clamps with a paddle are attached to the current-carrying rods, which ensures the connection of a bus or cable lugs. The oil conservator ensures the presence of oil in all operating modes of the transformer and fluctuations in ambient temperature, and also has a built-in air dryer with an oil seal. A thermometer is installed on the lid to measure the temperature of the upper layers of oil. Transformers with power from 400 to 2500 kVA are equipped with rollers. Transformers comply with GOST 116777 and technical specifications TU U31.1-31617591-001-1005.

All types of Lighting Poles and High Masts with luminaries Stadium High Masts and Floodlights Polygonal Tubular Poles and Lattice Towers for Over Head Lines Raod and Street Lighting Poles and luminaries Welded type Lattice Poles and Towers Decorative Lighting Poles Flag poles with Raising Lowering System and Infinite Rotation Mechanism Stainlees steel or Aluminum Flag poles with manual mechanism CCTV, Traffic Signalization and Traffic Gantry Poles Antenna Monopoles and Towers Guard Rails for Highways Traffic Sign Posts

TLKJUC6A07-180 superiOrtec CAT6A TOOLLESS, RJ45, 180-DEG, KEYSTONE JACK, UNSHIELDED, 568A/B WIRING, WHITE

TLKJSC6A07-180 superiOrtec CAT6A TOOLLESS, RJ45, 180-DEG, KEYSTONE JACK, SHIELDED, 568A/B WIRING, WHITE

TLKJUC607-180 superiOrtec CAT6 TOOLLESS, RJ45, 180-DEG, KEYSTONE JACK, UNSHIELDED, 568A/B WIRING, WHITE

TLKJSC607-180 superiOrtec CAT6 TOOLLESS, RJ45, 180-DEG, KEYSTONE JACK, SHIELDED, 568A/B WIRING, WHITE

MP24KJR-180 superiOrtec 1U CAT6 24-PORT, KMJ MODULAR PATH PANEL (UNLOADED FOR 180-DEG JACK) W/STRAIN RELIEF BAR, EMPTY

CL004C6AF/UTP-LS superiOrtec F/UTP CAT 6A 4PR LSZH CABLE - 23 AWG, 305M/ROLL

CL004C6AU/FTP-LS superiOrtec U/FTP CAT 6A 4PR LSZH CABLE - 23 AWG, 305M/ROLL

CL004C6AU/UTP-LS superiOrtec U/UTP CAT 6A 4PR LSZH CABLE - 23 AWG, 305M/ROLL

CL004C60U/FTP-LS superiOrtec U/FTP CAT 6 4PR LSZH CABLE - 23 AWG, 305M/ROLL, LSZH

CL004C60U / UTP-PE superiOrtec UTP CAT 6 4PR OUTDOOR ON CABLE, 305M / ROLL, PE

Marine air compressors and installations are used on ships: - to launch the main diesel installation; - to provide facilities with high-pressure compressed air; - filling with air and maintaining pressure in ship air guards; - refueling cylinders of breathing apparatus.

Compressors of this group are used in technological processes where compression of various gases (except air) is required, including aggressive, poisonous, explosive, inert and toxic. These compressors are used, for example, in the oil industry to create excess pressure in oil wells, in gas-flare facilities of oil refineries, in many technological processes of the chemical industry, in the space industry to create high-pressure dry nitrogen reserves, etc.

ENERGOSERVICE-M LLC is a leading Ukrainian enterprise in the supply of industrial refrigeration equipment with highly qualified engineering and production personnel and modern technological equipment. ENERGOSERVICE-M LLC - is a supplier of crane and autonomous air conditioners to ensure the safe operation of technological equipment, maintain the required temperature and humidity, clean it from harmful impurities: Autonomous industrial air conditioners: KA1-25 (KA2-25), KA1-40 ( KA2-40), KSA-15 (2KSA-15), KSA-20 (2KSA-20), KSA-25 (2KSA-25), KSA-45 (2KSA-45), 1KSA-15 (3KSA-15), 1KSA-20 (3KSA-20), 1KSA-25 (3KSA-25), 1KSA-45 (3KSA-45), KSA6.5 / 25 (1KSA6.5 / 25), KSA-3/15 (1KSA-3 / 15) are installed in industrial and office premises: 1) Control panels (posts) on rolling mills ( CA-15, KSA-20, KSA-25); 2) Control panels in the heat-power workshop (KSA-15, KSA-20); 3) Mashrooms (KSA-25, KSA-45); 4) Electrical facilities (microprocessor, thyristor, local telephone exchanges); 5) Laboratories (chemical, quantometric); 6) Service premises (conference rooms, canteens, change houses).