Construction mixtures in bulk on Qoovee

The active anti-rust pigment is recoated after about 1 hour. lead-free and chromate-free, active primer free from rust, dry fast. Can be recoated after a short time with synthetic resin paints. As a rust protection primer for iron parts, iron gates, steel structures, vehicles, machines, etc. Consumption approx. 150 - 200 g / m² per coat Color gray green, oxide red, white

ready-to-use non-bribery reinforcement for leveling absorption based on hydrosol Ready-to-use non-pigmented deep primer based on high quality acrylic hydrosol. For embedding and deep priming. Hardens slightly sandy substrates and leads to absorption equalization for highly absorbent substrates. Low emission and no solvents. Consumption about 100 - 200 ml / m²

- good priming effect high yield water dilutable Solvent free, water dilutable primer concentrate based on high quality acrylate. Good soil effect, high yield, environmental friendliness. For strengthening sandy and highly absorbent substrates, obtaining a uniformly absorbent substrate, and promoting adhesion of subsequent coatings both indoors and outdoors. Dilution up to 1: 4 with distilled water, depending on the nature of the surface. Consumption about 150 - 200 ml / m² per layer Colorless

water thinnable weather resistant fast drying Water thinnable, matt polyurethane acrylic paint with excellent processing properties. Shock resistant, scratch and shock resistant, very good flux, high coverage. For interior and exterior matt finishes for high quality coatings on wood, metals, rigid PVC and mineral substrates (note substrate pretreatment). Tinted in the shade in groups 1 - 4. Tintable in 171 RAL and over 40,000 other shades. Consumption approx. 100 - 130 ml / m² per coat Color White, transparent base. Can be tinted with the Murexin MIX system.

Oil-free impregnation for exterior wood surfaces. Good drying, high permeability, good weatherability (pearl effect) and weatherability. Resistant to bacteria and fungi. Mix container well, keep container tightly closed after use. Remove dust, dirt, grease and wax from wood. Treat with a brush, roller or sprayer. Consumption 250 ml / m² per coat Color natural brown

high coverage primer for efficient performance for sandy and absorbent substrates White, solvent-free, dispersion based primer. High quality titanium dioxide for high coverage. For indoor and outdoor walls and ceilings. For subsequent coating on dispersion and silicon resinous base. Do not use on highly absorbent or sandy substrates. Ideal as a base coat for dry lining. It can also be used as a top coat. Consumption approx. 100 - 150 ml / m² Color

ready to process waterproof low pollution permeable Ready to process, paste-like, thin-layer synthetic resin render for onlays and decorative elements. Etched thin plaster, white or colored, for indoor and outdoor use. Can be processed by hand or by machine. Water-repellent, weather-resistant, permeable, washable, low tendency to contamination, easy to process, universally usable. Consumption 1.0 mm grass structure 2.0 kg / m², Quality assurance: Own monitoring by our own factory laboratory. Third party monitoring of ongoing production control by a notified body.

Wear-resistant water-based insulating paint for insulating coatings on walls and ceilings on mineral substrates, as well as wood, non-ferrous metals and rigid PVC, both indoors and outdoors. Can be used as an adhesive and top coat on a variety of problem substrates. Consumption approx. 150 - 200 ml / m² per layer Color White; can be painted in full tones, base and shaded colors and in a color shade group, through the Murexin MIX system. EAN: 9002438120276 Art-Nr: 12027

Heat-insulating mixture - ready-made heat-insulating dry mixture for horizontal application. It is used to create monolithic thermal insulation screeds on the roof and indoors.

THERMOZON Ltd., a modern plant for the production of insulation, offers a 2 in 1 material in the form of thermal insulation plaster. Heat-insulating plaster & ndash; material for thermal insulation and wall plastering in one go. It is used on concrete surfaces, brick, aerated concrete, foam concrete masonry. THERMOZON provides a guarantee for its product.

Hydrophobizing compound for imparting water-repellent properties to porous building materials. To protect facades, lime and cement plasters from atmospheric moisture and capillary suction. Purpose Crystallisol Hydrophobizator: It is used for processing porous building materials: concrete, brick, gypsum, wood, plaster. The walls of the pores and all particles of the material in contact with the water repellent are enveloped in an invisible thinnest water-repellent film. The processed material loses its ability to be wetted with water and to absorb it capillary. When the composition is applied to the surface, a thin layer of polymer is formed on the pore walls, which is not wetted with water and does not allow water to penetrate into the pores. Crystallisol Hydrophobizator leaves the pores open, and the vapor permeability of building materials remains almost at the original level. Due to the device of a hydrophobic barrier, the material acquires water-repellent properties that persist for a long time, increasing its resistance to pollution and mold damage. When processing the facade, it is recommended to carefully apply the material to the surface, avoiding contact with glass, plastic window frames and other parts of the structure that do not require processing. Before applying, cover such places with paper, construction tape. Description Crystallisol Hydrophobizator: An aqueous solution based on methylsiliconates, which, penetrating into the pores of the structure, protect it from capillary inflow of water by changing the contact angle of the surface wetting. Properties Crystallisol Hydrophobizator: Possesses high chemical resistance and resistance to weathering. Does not form a surface layer. Does not prevent moisture evaporation from the material. Gives water and dirt repellent properties to materials. Retains the color and texture of the surface. Fireproof. Carry out work in dry weather at a temperature of at least + 5 ° C. Material consumption: 1 liter of concentrate - 155 m² of surface. Packing: polyethylene canister 1 l.

Complex for chemical milling of concrete and enhancing the adhesion of waterproofing coatings and self-leveling floors with a concrete surface. Purpose of Crystallisol CHIMFREZ / ACTIVE: Chemical milling of concrete surfaces (removal of the cement film) without destroying the cement stone, opening the pores of concrete and increasing the adhesion strength with monolithic concrete, with self-leveling floors, with tile adhesive, with cement, gypsum , magnesia screeds and plasters, with cement-based waterproofing materials, with interior and exterior cladding made of natural and artificial stone. Crystallisol CHIMFREZ dissolves the cement film and opens the pores of the concrete, Crystallisol ACTIVE adhesively activates the cleaned surface and increases the adhesion strength of the new layer with the previously laid one. They are used only in a complex: first, the concrete surface is treated with Crystallisol HIMFREZ, one hour later - with Crystallisol ACTIVE. Properties Kristallizol CHIMFREZ / ACTIVE: Effective for working on concrete grade up to M300. Replaces / complements mechanical and machine hydro-blasting of concrete surfaces. Eliminates "cold seams" in monolithic construction. Apply by brush or roller. The work is carried out at an ambient temperature of + 5 ° C. The compositions are fireproof. They are odorless. They do not have a harmful effect on humans and the environment. Does not contain hydrochloric, acetic, citric, orthophosphoric acids and substances that destroy concrete. Material consumption: 0.1 - 0.3 l / m² (depending on the condition of the surface). Packing: plastic cans 10 l.

Fast-hardening compound for the elimination of local active leaks. Setting time from 30 seconds to 3 minutes. Purpose Kristallizol GIDROPLOMBA: To protect concrete, reinforced concrete, stone and brick structures from water penetration and exposure to aggressive media. It is used to eliminate pressure leaks through cracks, seams, technological holes in structures. Ambient temperature during application from + 5 ° C. Properties of Crystallisol GIDROPLOMBA: Composition hardening time from 30 seconds to 3 minutes. High water-stopping properties. Resistant to aggressive environments. Breathable. Environmentally friendly, non-toxic. Fireproof. Material consumption: 2 kg / dm³ (a ball with a diameter of 9-10 cm is obtained from 400 grams). Packaging: 2 kg bucket.

Complex additive in concrete solution to increase concrete water resistance. Purpose of Crystallisol MONOLIT: It is recommended to use Crystallisol Monolit as a complex waterproofing additive in a concrete solution at the stage of construction of hydraulic structures, civil and industrial construction, tunnels, overpasses, bridges, when installing concrete screeds, etc. The grade of concrete to which it is planned to add Crystallisol Monolith as an additive to increase its water resistance must be at least M150. Properties of Crystallisol MONOLITH: Increases the strength and density of concrete. Increases the water resistance of concrete. Increases the frost resistance of concrete. Does not reduce the protective properties of concrete in relation to reinforcement. Compatible with plasticizing and anti-freeze additives. Resistant to aggressive environments. Environmentally friendly, non-toxic. Material consumption: 1% by weight of cement. Packaging: 15 kg bucket.

One-component flexible waterproofing sealant for all types of surfaces. Purpose of Crystallisol Elast: To create a thin (2-4 mm) waterproof layer applied both outside and inside structures subject to dynamic loads. With a layer thickness of 2 mm, it is capable of bridging cracks over 0.9 mm, the elongation at break is about 10%. It is used for work in tanks with drinking water without limiting the dimensions of the structure. The final layer resembles an elastic rubber and has high adhesion to all possible surfaces. The treated surface, due to its high adhesion, does not flake off and is able to withstand significant mechanical stress. With a layer thickness of 4 mm, after 7 days of normal hardening, water resistance is achieved at the level of W14 at water pressure "on the hold-down" and W8 at the "pull-off" pressure. Description Crystallisol Elast: Crystallisol Elast is a dry mixture of Portland cement, calibrated quartz sand and chemically active additives. Application thickness for 1 pass up to 4 mm. Ready time - 3 days. Properties of Crystallisol Elast: Waterproof at hydrodynamic pressure up to W14. Low shrinkage deformations. High curing rates. High fracture toughness. Resistant to aggressive media, acid-alkali-resistant. Works on all types of substrates, including metal ones. Environmentally friendly, non-toxic. It is applied both from the inside and from the outside of the structure. Closed with tap water at room temperature. It is applied with a spatula or brush. Material consumption: 3 kg / m² with a layer thickness of 2 mm. Packaging: 25 kg bag.

Repair and restoration plaster waterproofing material of penetrating action. For repair, restoration and waterproofing of old concrete and destroyed brickwork, as well as for leveling the surface. Purpose Kristallizol Repair: For the repair of concrete and brick destroyed structures in order to ensure water tightness, increase strength and frost resistance. Restoration and leveling of destroyed areas on concrete and brick, waterproofing plaster surface coating. Description Crystallisol Repair: Crystallisol Repair is a mixture of Portland cement, calibrated quartz sand and chemically active additives. Properties Crystallisol Repair: Waterproof under hydrostatic pressure W8. It is used for work on old, destroyed concrete and brick structures. Forms a waterproof armored layer. It is applied both from the inside and from the outside of the structure. Increases frost resistance and structural strength. Resistant to aggressive environments. Environmentally friendly, non-toxic. Closed with tap water at room temperature. It is applied on a surface saturated with moisture. Material consumption: 1.3 - 1.5 kg / m² with a layer thickness of 1 mm (depending on the surface condition). To achieve a waterproofing of 8 atmospheres, a layer of 10 mm is required. Packaging: 25 kg bag.

Non-shrinking joint waterproofing material of penetrating action. It is used to eliminate water filtration through abutment joints, cracks, chips of concrete and brick structures. Purpose Crystallisol Suture: For internal and external waterproofing of joints in underground and buried structures: horizontal and vertical joints of concrete and brick structures, seams of foundation blocks, brickwork, "cold joints", etc. Description Crystallisol Suture: Crystallisol Suture is a mixture of Portland cement, calibrated quartz sand and chemically active additives. Properties Crystallisol Suture: Waterproof under hydrostatic pressure W8. It is used for work on both old and new concrete and brick structures. Resistant to aggressive environments. Non-shrinking, does not require additional maintenance. Increases the frost resistance of the structure. Environmentally friendly, non-toxic. Closed with tap water at room temperature. It is applied on a surface saturated with moisture. It is applied both from the inside and from the outside of the structure. Material consumption: 0.9 - 1 kg / lm (with a groove section of 20x20mm). Packaging: 25 kg bag, 15 kg bucket

Penetrating waterproofing material for work on new concrete surfaces in the absence of groundwater filtration at the time of work. Apply with a brush. Purpose of Crystallisol W12 Kistevoy: For internal and external waterproofing of concrete structures in underground and buried structures operating under conditions of constant or variable exposure to the aquatic environment: foundations and basements located below the groundwater level, water reservoirs, hydraulic structures, overpasses, pools, etc. It is applied to the surface in the absence of strong water filtration at the time of work. Not used for brickwork. Description Crystallisol W12 Kistevoy: For internal and external waterproofing of concrete structures in underground and buried structures operating under conditions of constant or variable exposure to the aquatic environment: foundations and basements located below the groundwater level, water reservoirs, hydraulic structures, overpasses, pools, etc. It is applied to the surface in the absence of strong water filtration at the time of work. Not used for brickwork. Properties Crystallisol W12 Hand: Waterproof under hydrostatic pressure W12. It is used for work on new concrete structures. Increases frost resistance. Resistant to aggressive environments. Environmentally friendly, non-toxic. It is applied both from the inside and from the outside of the structure. Closed with tap water at room temperature. It is applied with a brush on a surface saturated with moisture. Material consumption: 0.8 - 1 kg / m² (depending on the condition of the surface). Packaging: 25 kg bag, 15 kg bucket.

Water-stopping waterproofing material of penetrating action. For work on concrete and brick surfaces with strong filtration of groundwater. Purpose of Crystallisol W12: For internal and external waterproofing of concrete, stone and brick structures in underground and buried structures operating under conditions of constant or variable exposure to the aquatic environment: foundations and basements located below the groundwater level, water reservoirs, hydraulic structures, overpasses, swimming pools etc. It is used as a repair compound in the restoration of damaged concrete surfaces or masonry. It is applied on concrete / brick surfaces even with strong water filtration. It can be used as a complex waterproofing additive in concrete at the stage of construction, at the rate of 5% by weight of cement. Description Crystallisol W12: Crystallisol W12 is a mixture of Portland cement, calibrated quartz sand and chemically active additives. Properties Crystallisol W12: Waterproof under hydrostatic pressure W12. It is used for work on both old and new concrete structures. Increases frost resistance. Resistant to aggressive environments. Environmentally friendly, non-toxic. It is applied both from the inside and from the outside of the structure. Closed with tap water at room temperature. It is applied with a spatula on a surface saturated with moisture. Material consumption: 2.5 - 3 kg / m² (depending on the surface condition). Packing: 25 kg bag, 15 kg bucket.

They are mainly used for anti-filtration protection of concrete and brick structures in order to create a waterproofing layer on horizontal (including ceilings) and vertical surfaces. Ready-to-use does not require warming up. Contains cement and fiber filler.

Ready-to-use waterproofing mastic. Mastic is perfect for waterproofing foundations, basements, floor slabs

High quality building plaster.

Dry building mixes at wholesale prices.

ALBUS Portland cement M-400 grade: Loose - 590 sum Ordinary bag - 670 sum Brand bag - 690 sum ALBUS Portland cement M-500 grade: Brand bag - 790 sum Payment term: Bank transfer

Water based PVA glues AQUASIVE. Application area: textile lamination, woodworking, paper and packing and ect.

Hot melt adhesives POWERMELT Application area: woodworking, food packaging, bookbinding, pocket spring, matresses production,carpets,cord strapping,labeling,hygiene and etc.

Solvent based adhesives GUCLU. Application area: furniture, wood and automotive sectors, shoe and leather sector.

Ready-made dry glue (mixture) based on cement binder with polymer additives. It is used for gluing such finishing materials as faience and ceramic tiles, marble and granite slabs, glass mosaic screed, etc. on the surface of the screed, concrete in closed and open areas, in horizontal and vertical surfaces, tiled, etc. tiles.

Ready-made dry glue (mixture) based on cement binder with polymer additives. It is used for interior and facade works for gluing ceramic, faience, tile, etc. tiles.

Dry building dispersion putty mixture on a gypsum basis, with polymer additives, manufactured in accordance with GOST 31387-2008. Universal gypsum putty FUGA is intended for: - Thin-layer spackling of gypsum plasterboard and gypsum fiber sheets; - Filling the joints of precast concrete elements; - Bonding plasterboard sheets and combined panels to a flat surface; - For interior work. Easy to apply, smooth and sand. It has good adhesion to concrete and drywall. It allows air to pass through and thereby balances the humidity level. Very lightweight, provides thermal insulation. Has fire-fighting properties.

Dry building dispersion putty mixture on a gypsum basis, with various additives, manufactured in accordance with GOST 31387-2008. Designed for leveling stone, brick, plaster and other surfaces during interior work during construction, repair and reconstruction of buildings and structures. The putty mixture can also be used as a base for the subsequent application of decorative coatings (paints, etc.). Easy to apply, smoothen and sand. It has good adhesion to concrete and drywall. Does not roll up when applied to subsequent layers and does not crack when dry. Creates a flat and smooth surface for painting and wallpapering. It allows air to pass through and thereby balances the humidity level. Very lightweight, provides thermal insulation. Has fire-fighting properties.

Dry building putty mixture made on gypsum binder with various additives in accordance with GOST 31387-2008. Possesses high adhesive properties. It is intended for preparation of surfaces for finishing when carrying out interior work on concrete, cement screed or gypsum plaster and on other surfaces of gypsum bases. Layer thickness for one application - 1mm. Creates a flat and smooth surface that does not need a primer, for painting or wallpapering. When dry, it does not crack and allows air to pass through and thereby balances the moisture level. Very lightweight, provides thermal insulation. Does not drain or collect. Has fire-fighting properties.

Gypsum-based dry plaster mix, manufactured in accordance with GOST 31377-2008. Used for interior work for leveling and plastering stone, brick, gypsum, concrete, monolithic concrete, etc. surfaces. It is applied with a layer thickness of 5 mm to 50 mm. It has high adhesive properties and does not need additional materials. Does not drain or collect. It allows air to pass through and thereby balances the humidity level in the rooms. Provides thermal insulation. Has energy-saving and fire-fighting properties.

Wholesale and delivery of cement from Turkey.

Purpose: Designed to destroy and prevent the formation of mold, fungi, mosses, lichens on mineral materials (stone, concrete, gypsum, plaster, ceramic tiles, gypsum plasterboards, etc.) and wood (plywood, fiberboard, chipboard, etc.) .). Recommended for processing facades and basements of buildings, fences, rooms with high humidity (basements, cellars, kitchens, bathrooms, greenhouses). It can be added to unmodified plaster, masonry mortars, putty as a biocidal additive instead of mixing water. The tool perfectly sanitizes the surfaces of walls, brickwork, ceilings, interpanel seams. Has a long-lasting effect.   Benefits: long-term protection up to 15 years; effectively protects against biological damage and insects; environmentally friendly, does not contain solvents; does not damage or stain the treated surfaces. as a biocidal additive instead of mixing water.   Mode of application: The product must be diluted with water. Apply an antiseptic with a brush, roller, spray 2-3 times after each previous layer has dried. When treating an already affected surface, apply an antiseptic, after 24 hours clean the surface and repeat the treatment. When processing mineral surfaces directly exposed to water, cover it after drying with a water repellent GKZH-11 or waterproof paints and varnishes. Average consumption 100-150 g / sq. m on mineral grounds and 200-300 gr./sq. m for wood. When used as a biocidal additive in mortar mixtures, test with a small amount for compatibility. Water-borne paint: add 250 ml of paint to 20 liters of paint and mix thoroughly. Additive to plaster: 250 ml of the product is enough for 10 liters of water. Grout or plaster is mixed on the resulting solution. Grout: 50 ml is added to the mixing water per 5 kg of dry mass. Additive to wallpaper glue: add about 25-30 ml of active agent per 1 liter of water to the glue mixing liquid, then prepare the glue according to the instructions. Precautions: When working, use protective equipment for skin, eyes and respiratory organs (rubber gloves, overalls, glasses, respirator). In case of contact with skin, mucous membranes, eyes, rinse immediately with plenty of running water for 10-15 minutes. Seek medical attention if necessary. Danger: Possible irritant effect on the skin. Storage and transportation: Transport and store at temperatures from + 5 ° C to + 40 ° C, in a hermetically sealed original container, separately from food, in a cool ventilated room, out of the reach of children and animals. Avoid heating and direct sunlight. The composition retains its properties after short-term freezing. Dispose of in accordance with SanPin 2.1.7.1322-03Shelf life: 36 months

Fire retardant compound with a powerful antiseptic effect for outdoor and indoor use. It is an aqueous solution of highly effective fire retardants, antiseptics, fungicides and functional additives. Protects wood from fire and the spread of flame indoors for up to 16 years, provides 1 group of fire retardant efficiency in accordance with GOST R 53292-2009 at a consumption of 270 gr. per m², and for up to 30 years from decay, mold, damage by wood-boring insects at a consumption of at least 100 gr. per m². The composition is environmentally friendly. Possibly perform processing to -20 ° C. Does not salt out on the surface. Tones wood in a pleasant amber shade.

Fire retardant compound with a powerful antiseptic effect for outdoor and indoor use. It is an aqueous solution of highly effective fire retardants, antiseptics, fungicides and functional additives. Protects wood from fire and the spread of flame indoors for a period of at least 15 years, provides 1 group of fire retardant efficiency according to GOST R 53292-2009 at a consumption of 275 g / m2, and for up to 25 years from rotting, mold, insect damage woodworms at a consumption of at least 100 g / m². The composition is environmentally friendly, the pH of the composition is 5.5 - 5.7 - which corresponds to the acidity of the skin of an average person and is made from raw materials marked "FOOD" - for food production. Can be processed down to –25 ° C. Does not salt out on the surface and does not tint the wood. After processing with the Kaisar "Premium" composition, any glazing compositions can be applied.

Hydroizol "Haveg" is often used for roof protection. This material is extremely easy to apply, which allows you to quickly process the surface. It is very easy to apply a layer of liquid rubber, and it can be done with various tools. Temperature Stability: Resistance of the waterproofing cover to any temperature: from -50C ° to + 85C ° Durability: The service life of the finished coating is up to 30 years. Absolute UV protection. Impact resistance: The coating is resistant to shock loads both at positive and negative temperatures.   Source and copyright holder:

We are Geoser company from Turkey, a manufacturer of Geosynthetic and waterproofing materials such as HDPE, PVC, LDPE, EPDM and Waterstops. we can provide Geomembrane and Liners in a variety of physical, mechanical, and chemical resistant properties.

We bring to your attention the products of our plant - SoftRock Stone Finishing Coating. It is a water-dispersive polymer coating with a mineral filler and UV inhibitors in its composition. The coating has the following consumer properties and characteristics: · Does not fade; · Possesses high adhesion; · Forms a dense layer on the surface; · Vapor permeable; · Moisture resistant; · Does not create smudges; · Resistant to stretching; · Has high weather resistance; · The surface is covered with a protective film, which prevents the absorption of dust, dirt, etc .; · Simple to use; · Provides high speed of application; · Has a wide range of colors, can be tinted like paint; · Does not deteriorate for more than 25 years. The coating is applied with a texture gun or trowel. The standard consumption is 1.2 kg / m2 on a primed surface, with a layer thickness of 0.8 mm. Stir with a mixer before use! Instructions for applying with a textured (cartridge) pistol: Nozzle 4 mm, mixture supply no more than 30% of the total range of the pistol valve. The compressor is recommended with a receiver from 50 liters. The coating is applied in a circular motion from a distance of 30-40 cm. The mixture is diluted with water in the range of 150-250 ml per 17 kg bucket, no more! Surface preparation: 1. Deep penetration primer. 2. When painting in dark colors, the coating is applied in one layer. 2.1. When painting in light colors, it is recommended to cover the base with acrylic paint of the same color, then apply the stone coating in one layer.