Construction mixtures in bulk on Qoovee

PURPOSE: Used for waterproofing static cracks, seams, joints, service entries, interfaces and junctions in concrete and reinforced concrete structures. DESCRIPTION: Dry, fine-grained, waterproofing, surface mixture Pk1, B30, W14, F300 “Penekrit” GOST 31357-2007. It consists of Portland cement, quartz sand of a certain granulometry, and active chemical components. ADVANTAGES: - High strength and water resistance; - High adhesion to the base; - No shrinkage; - Used in domestic and drinking water supply. Scope of application of waterproofing material Penecrit. Used for waterproofing static cracks, seams, joints, communication entries, interfaces and junctions in concrete and reinforced concrete structures. High strength and waterproof. High adhesion to the base. No shrinkage. Used in domestic and drinking water supply. Dry mixture consumption 1.5 kg/m.p. (fine 25x25 mm), with an increase in the cross-section of the fine, the consumption increases proportionally. Surface preparation. Using a wall chaser and a jackhammer, make a groove with a cross-section of at least 25x25 mm along cracks, seams, joints, utility entries, connections, and junctions. Thoroughly clean the surface from debris and loose concrete using a brush with metal bristles, moisten it generously and prime it with one layer of Penetron mortar mixture (consumption 0.1 kg/m.p.). Preparation of mortar mixture. Use clean water and containers. Mix with water in a proportion of 0.14 - 0.16 liters of water per 1 kg of dry mixture or 1 part water per 5 parts of dry mixture by volume for 2 minutes until a thick plasticine-like consistency is obtained. Use within 30 minutes, stirring regularly without adding water.

Penetron – penetrating waterproofing of concrete. The service life of penetrating waterproofing is equal to the service life of building structures. Penetron is approved for waterproofing in domestic and drinking water supplies. Penetrating waterproofing gives concrete the properties of “self-healing” cracks with an opening of up to 0.4 mm. Concrete penetrating mixture can be applied with either forward or reverse water pressure. There is no need to dry the concrete surface before applying penetrating waterproofing. The water resistance, corrosion resistance and frost resistance of concrete increases. Penetrating waterproofing maintains the vapor permeability of concrete. Purpose. Penetrating mixtures Penetron are used for waterproofing concrete and reinforced concrete structures. As a result, their water resistance increases and concrete acquires the ability to “self-heal” cracks with an opening of up to 0.4 mm. For waterproofing static seams, cracks larger than 0.4 mm and utility entries, it is used in conjunction with other materials of the Penetron system. Dry mixture consumption 0.8 - 1.1 kg/m2 when applied in two layers. Surface preparation. Before applying the penetrating mixture, the surface is cleaned to structurally sound concrete. Wet the concrete with water until it is as saturated as possible.

Penetron Admix Waterproofing additive for concrete (Penetron Admix) DESCRIPTION: Dry waterproofing additive for concrete mixture. Consists of special cement and active chemical components. PURPOSE: Used for waterproofing concrete and reinforced concrete structures by increasing their water resistance and acquiring the property of “self-healing” cracks with an opening of up to 0.4 mm. ADVANTAGES: - Increased water resistance, durability, frost resistance and corrosion resistance of concrete; - Elimination of additional waterproofing of structures/products; - Compatibility with any other additives (plasticizing, antifreeze, air-entraining, etc.); - Used in domestic and drinking water supply. Instructions for use of materials. The application temperature for the Penetron Admix additive complies with current standards at which concrete work is possible. CONSUMPTION: 1% by weight of cement in the concrete mixture or 4 kg of additive per 1 m3 of concrete mixture. METHODS OF ADDITIVE ADMINISTRATION: Introduce Penetron Admix into a concrete truck in the form of a solution in the proportion of 2.5 liters of water per 4 kg of dry additive or 1 part water to 1.5 parts dry additive by volume. Use the prepared additive solution within 5 minutes. Mix the solution in a concrete truck for at least 10 minutes at high mixer speeds. In dry form, the Penetron Admix additive is administered through the dry additive dispensers of the RBU production line. It is possible to introduce a calculated amount of additive along with inert materials. When concreting, ensure waterproofing of technological seams and joints using a waterproofing harness “Penebar” and “Metal fastening brackets”. PRECAUTIONARY MEASURES: Use rubber gloves, cotton gloves, a respirator, goggles, protective clothing made of thick fabric, boots. If the mixture gets on your skin or eyes, rinse immediately with water and consult a doctor. Technical characteristics of the additive Penetron Admix. Name of the indicator. Meaning Measurement methods. Technical characteristics of the dry additive. Moisture by weight. Not more than 0.6% GOST 8735 Bulk density 1020 ± 70 kg/m3 Technical characteristics of concrete with additive. Increasing the waterproof grade. At least 3 levels GOST 12730.5 Increased frost resistance, cycles, at least. At least 100 cycles GOST 10060.0Additional characteristics. Package. Multilayer bags (20 kg), plastic buckets (25 kg). Storage and transportation conditions. Store multilayer bags in dry rooms, plastic buckets at any humidity and temperature. Guaranteed shelf life: 12 months in multilayer bags, 18 months in plastic buckets, provided the original packaging is sealed intact.

AVG Polyurethane Foam 65 gross weight 850g, Winter / Summer.

The redispersible latex powder product is water-soluble redispersible powder, which is divided into ethylene/vinyl acetate copolymer, vinyl acetate/ethylene tert carbonate copolymer, acrylic acid copolymer, etc. The powder adhesive made after spray drying uses polyvinyl alcohol as protective colloid. This kind of powder can be quickly redispersed into lotion after contacting with water. Because redispersible latex powder has high adhesive ability and unique properties, such as water resistance, workability and heat insulation, their application range is extremely wide. Ceramic tile adhesive Adhesive mortar for external wall insulation system [1] External wall insulation system plastering mortar Ceramic tile pointing agent Self flowing cement mortar Flexible putty for interior and exterior walls Flexible crack resistant mortar Rubber powder polystyrene particle insulation mortar Dry powder coating Polymer mortar products with high requirements for flexibility.

For tinting oils and wax, we recommend using our tints, which easily give the desired shade while maintaining the decorative effect of the wood grain. Our unique paint and varnish coating formulations are based on natural and modified natural ingredients. The composition of Nevskaya Artel products includes such ingredients as: linseed oil, pine resin, beeswax, gum turpentine. The entire line of our wood processing products is manufactured in Russia using domestic raw materials, which eliminates dependence on imports.

deep penetration primer from the manufacturer, different price segment.

It’s well known that strengthening concrete with steel bars results in a combination stronger than either material alone. It’s also commonly understood that concrete’s high pH (alkalinity) normally provides protection for the steel against moisture-induced corrosion. Concrete’s high pH levels – typically pH 12-13 – will produce a thin oxide layer on the steel, preventing the reaction of the metal atoms. This thin zone is known as a passivity layer or film. It does not actually prevent corrosion, but greatly reduces it. This protective passivity layer can be destroyed, either by reduction of the alkalinity or by an increase in chloride ions. Alkalinity can be decreased by carbonation of the concrete. This is a very slow process, commonly seen as surface whitening in ageing structures. Chloride is the better-known cause of concrete corrosion and is a serious issue with marine structures. For reasons not fully understood, chloride ions will penetrate the passivity layer, leaving the steel vulnerable to corrosion. Significantly, only water-soluble ions have this effect. Key point 1: Reactive contaminants are carried to the steel by moisture. This is why minor cracking and micro-cracking in concrete, whether by movement, low cover shrinkage, or conditions such as ASR or DEF, is a very real threat. Key point 2: Minor cracks encourage the penetration of moisture vapour and moisture-borne contaminants. Here’s where PROTEX can help. The application of a penetrating catalytic hydrogel PROTEX can close the porosity and micro-cracking of the concrete, to a crack width of up to 0.5 mm, and to a treatment depth of up to 150mm! This depth of treatment ensures the rebar zone is encapsulated. Moisture, moisture vapour, and moisture-borne contaminants, are immobilised. This is a seriously effective treatment. By capturing the movement of moisture in the concrete, and particularly by treating the concrete early in the deterioration process, corrosion can be arrested or even totally prevented. If you are in charge of budgeting for the maintenance of a structure, you will see the significance of this at once. This treatment will help prevent major concrete decay and increase in the structure’s service life. Think of the savings in maintenance and replacement costs, Think of PROTEX.

Construction mixtures

Construction concrete with delivery is required for the construction of reliable civil and industrial structures. This material is actively used in the construction of buildings and utilities, as well as in the production of reinforced concrete products. In addition, it is actively used: in the construction of temporary and permanent roads. when arranging the foundation of residential, utility and industrial premises. when repairing underground communications, engineering systems and road surfaces.

CRUMBER RUBBER BINDER: BINDER BINDINGS: KN-p (BINDER)SBR for seamless casting It is a low-viscosity, solvent-free binder that cures with atmospheric humidity. Connects and binds particles such as rubber granules, rims, polyurethane pieces, sponge flakes. It can also be used as a primer for adhesive and insulating purposes. Used in playgrounds, sports floors, walking paths and offices. One-component aromatic, brown-yellow Shelf life 9 months Packaging 220 kg drum

ready-to-use frost resistant especially for improvement work Ready-to-use dry concrete for concreting. Indoors and outdoors, for small concrete work, concreting of individual steps and concrete panels, as an extension of the screed for repair work, for concreting in gratings, ravines, etc. Consumption approx. 2.0 kg per 1 liter of fresh concrete

quick setting can be used indoors and outdoors reducing construction time Hydraulic bonding agent to produce cementitious screeds. Ready for installation in 7 days. Room for the production of composite screeds, screeds on composite layers and floating screeds as a laying substrate for various topcoats. Consumption about 2.5 kg/m² per cm of layer thickness

Low Viscosity Forced Setting Forced Setting 2-component, solvent free, food safe, saponification resistant, compression free and low viscosity reactive epoxy resin. The material also cures in thick layers and forms a positive and tight bond with the substrate. Indoors and outdoors for grouting and filling narrow and deep cracks, holes and cavities. Consumption about 1.1 kg per liter of filling space

is a true drying accelerator independent of moisture ready to lay can be accurately calculated Fluid, chloride-free, universal accelerator for cement bonded screeds. The addition of water can be reduced due to the liquefaction effect and a faster laying readiness is achieved. In addition, it positively affects the consistency of the screed, resulting in improved processing in relation to tightening and smoothing. To achieve earlier laying readiness and especially suitable for heating screeds. Consumption Dosage from 2.0% = 5.0 kg to 3.0% = 7.5 kg Ready to lay after 12-14 days: 1.25 kg Screed accelerator X4 Per screed mix (250 l) at W/B value : max. 0.45 Ready to install after 3 – 5 days: 1.9 kg Screed Accelerator X4 per screed mixture (250 l) at W/B value: max. 0.45 Consumption approx. 7.5 kg/m³ screed Colour: transparent yellow

color fast ready to use abrasion resistance Factory premixed, ready to use dry material consists of special, natural hard materials, Portland cement and dispersing agents. The spread product completely wets itself as it absorbs water from the concrete or screed mix and thus forms an extremely thick and compact painted surface. Low cost per m², high abrasion resistance, high impact resistance, high surface density, low oil and grease absorption, easier to clean. Consumption min. 3 kg/m² - depending on floor tension

colour fast ready to use abrasion resistance Hard grain spreader for concrete and screed floors. Factory pre-mixed, ready-to-use dry material consists of special, natural hard materials, Portland cement and dispersing agents. The inorganic pigments are resistant to cement, alkalis, light and guarantee long-term durability of the color of the floor. Dispersing agents absorb water from the concrete or screed mixture and thus form an extremely thick and compact painted surface. Low cost per m², high abrasion resistance, high impact resistance, high surface density, low oil and grease absorption, easier to clean. Consumption min. 3 kg/m² - depending on floor load

binds dust surface hardening high abrasion resistance Solvent-free, dust-binding, mineral, surface hardening impregnation for mineral substrates. Causes silicification of the surface and consequently increases the mechanical abrasion resistance. In addition, the impregnated, water- and dirt-repellent surface is achieved due to the high penetrating properties. Indoors and outdoors on horizontal and vertical mineral components. Consumption about 0.3 kg/m² depending on absorbency

plastic hardened without chlorides quick setting Powdery, hardened, chloride free, fast curing, hydraulic setting of flash setting solution. Indoors and outdoors, as well as in permanently wet areas, for fast installation for the transfer of dowels, door frames, handrails and washbasin consoles, as well as for improving and filling holes, cavities and cracks in concrete elements. Consumption of 1 kg gives about 0.7 liters of fresh solution

Single-component plastic-hardened quick setting one-component, cementitious, plastic reinforcement protection. The Repol BS7 reinforcing protection is very easy to process and does not require the application of quartz sand. Thanks to the mineral base components and the quick set recipe, excellent adhesion on steel and concrete is achieved. Consumption about 0.2 kg / sq.m of reinforcement in two stages of work. ColorGray

Frost/anti-freeze wear resistant agent can be combined with gray concrete aggregate Mineral, powdered, hardened, weather resistant, hydraulically settable white aggregates for concrete repair in accordance with EN 1504-3 class R2. Indoors and outdoors for extensive filling of concrete surfaces, improving unevenness, gravel pockets, broken edges, wear to damaged areas, etc. For exposed concrete, different gray shades can be achieved and thus adapted to different concrete substrates by mixing in BS 05 Gray concrete filler. Consumption approx. 1.5 kg/m² mm

Frost/anti-freeze wear resistant agent can be combined with white concrete aggregate Mineral, powdered, hardened, weather resistant, fast setting, hydraulically settable gray aggregate for concrete repair, according to EN 1504-3 class R2. Indoors and outdoors for extensive filling of concrete surfaces, etc. For exposed concrete, by mixing in concrete filler BS 10 White various gray colors can be achieved and thus adapted to different concrete substrates. Consumption approx. 1.5 kg/m² per mm layer thickness

frost resistant quick set up indoors and outdoors Powdery, hardened, weather resistant, fast setting, hydraulically set filler. Indoors and outdoors for optical correction of defective, mottled concrete surfaces full of pores to achieve an even, smooth surface. Layer thickness max. 2 mm. Coverage approx. 1.4 kg/m² per mm layer thickness

Chloride-free liquid can be processed down to -9 °C Chloride-free, liquid frost-resistant agent for concrete and mortar. The addition increases the heat of hydration of the concrete or mortar and therefore the required minimum compressive strength of 5 N/mm² for the freeze resistance achieved previously. Indoors and outdoors for reinforced concrete and prestressed concrete as well as mortar. Allows concreting and masonry work at -9 °C when standardized protective measures are observed. Consumption about 1% by weight of cement (about 3 - 4 kg/m³ of concrete)

chloride-free plasticizing liquid Chloride-free, liquid concrete and mortar additives without the introduction of air pockets. Increases displacement and improves processability while reducing W/B and increasing flexural and compressive strength. Reduces the tendency to split and bleed. Indoors and outdoors. Consumption about 3 - 4 kg/m³ concrete/mortar

Cement binding frost resistant can be filled in gradients up to 3% stable and can be set to flow Powdered, plastic hardened, low stress, self leveling, hydraulically set leveling compound. For indoors and outdoors, especially for evening extreme unevenness such as hollow slabs and slabs, as well as large area level compensation up to 3% slope. Consumption approx. 1.6 kg/m² per layer thickness mm

Very fast curing Good bonding No waiting time for subsequent work Powdery, very fast curing, hydraulically setting bonding agent. Only indoors for fixing electrical installations, anchoring dowels, filling cracks. Consumption depending on use and application

Microsphere: Gray, 0-500 microns humidity 1% price from 1 to 5 tons, 71,000 rubles Gray, 0-500 microns humidity 1% price from 5 to 10 tons, 70,000 rubles Gray, 0-500 microns humidity 1% price from 10 to 20 tons, from 65,000 rubles Gray, 0-500 microns humidity 1% price from 20 tons, from 64,000 rubles The products are packed in BIG BEG (MKR), 500 kg each. TU 5712-089-15005227-2020

- siloxane-reinforced permeable good finish Siloxane-treated façade paint for high quality façade coatings in a wide range of colors. For lightfast, non-yellowing and alkali-resistant facade coatings with high adhesion strength of newly unpainted finishing plaster, as well as for repairing coatings with good old adhesive paints, both indoors and outdoors. Consumable layer with fine gypsum grain about 150 - 250 g / m², coarse gypsum grain about 250 - 350 g / m² Color Base white, colorless. Can be painted in full, base and shaded colors using the Murexin mixing system.

- isolates traces of nicotine, lignin and soot separates dry coffee and watermarks solvent-free odorless and splash-free excellent permeability Water-based wear resistant insulating paint for nicotine, coffee and soot stains, as well as lignin and water stains, as in indoors and outdoors. For insulating coatings on walls and ceilings on mineral substrates, as well as wood, non-ferrous metals and rigid PVC, both indoors and outdoors. Wet abrasion: Grade 1. Tip: Can be used as an adhesive and top coat on a variety of problem substrates. Consumption approx. 150 - 200 ml / m² per layer Color White; can be painted in full tones, base and shaded colors and in color shade group 1 through the Murexin MIX system.

- Low emission and solvent free abrasion resistance abrasion resistant matt Matt, abrasion resistant, solvent free latex color with high coverage and excellent processing properties. Combines the durability of latex paint with the matt surface of conventional dispersion paints. Tested in accordance with EN 13300: wet abrasion: class 1. For resilient, easily washable paints on interior walls and ceilings in new buildings and during interior refurbishment. Consumption approx. 150 - 200 ml / m² per coat Color Base white, colorless. Can be painted in full, base and shaded colors using the Murexin mixing system.

- ELF - low emission and solvent free, contains kaolin Wet abrasion class 2 Scrub resistant, kaolin containing interior emulsion paint, in the best decorating quality, with a high degree of coverage. Awarded with the Austrian Eco-Label. Wet abrasion: class 2; Opacity: Class 1. Consumption approx. 150 - 200 ml / m² per coat Color Base white, colorless. Can be painted in full, base and shaded colors using the Murexin mixing system.

- ready-to-use high filling power easy handling White ready-to-use hand-held filler for versatile indoor use. High filling capacity and pliability ensure smooth and precise processing of light sandy finishing aggregates. For standard filling work on indoor walls and ceilings, but also best suited for grouting works as well as for butt and surface filling. Layer thickness: up to 5 mm at each stage of work. Consumption approx. 1.5 kg / m² per layer mm Color white

- good primer effect high yield water dilutable Solvent free, water dilutable primer concentrate based on high quality acrylate. Good soil effect, high yield, environmental friendliness. For strengthening sandy and highly absorbent substrates, obtaining a uniformly absorbent substrate and promoting adhesion of subsequent coatings both indoors and outdoors. Dilution up to 1: 4 with distilled water, depending on the nature of the surface. Consumption about 150 - 200 ml / m² per layer Colorless

- Etkili Performans için Yüksek Kapatıcılı Astar Alçıpan levhalar için idealdir Beyaz, solventsiz, dispersiyon bazlı astar. Yüksek kapatıcılık için yüksek kaliteli titanyum dioksit. İç ve dış duvarlar ve tavanlar için. Dispersiyon ve silikon reçineli baz üzerine müteakip kaplama için. Çok emici veya kumlu yüzeylerde kullanmayın. Kuru astar için temel kat olarak idealdir. Ayrıca üst kat olarak da kullanılabilir. Tüketim yaklaşık 100 - 150 ml / m² Renk beyaz

for smoothing various materials ideal surface appearance Long-term protection Murexin Universal Smoother UG 1 is used for smoothing all Murexin silicone and polyurethane seals as well as Murexin natural stone silicones. Indoors and outdoors. Murexin Universal Smoother has the property of modifying the surface tension of the sealants used in such a way that pasty masses can be deformed without problems. This is not possible with water alone. Not suitable for dispersion based acrylic sealants. A 1.0 liter consumable bottle is sufficient for 60 m2 (determined in a standard climate, 20 ° C / 60% RH)

for smoothing various materials ideal surface appearance Long-term protection Murexin Universal Smoother UG 1 is used for smoothing all Murexin silicone and polyurethane seals as well as Murexin natural stone silicones. Indoors and outdoors. Murexin Universal Smoother has the property of modifying the surface tension of the sealants used in such a way that pasty masses can be deformed without problems. This is not possible with water alone. Not suitable for dispersion based acrylic sealants. A 1.0 liter consumable bottle is sufficient for 60 m2 (determined in a standard climate, 20 ° C / 60% RH)

admissible total deformation up to 15% coated with RAL UZ 123 (Blue Angel) free of solvents, phthalates, glycols, APEO-, isocyanate- and silokones free of organohalogen and organotin compounds Ready-to-use one-component acrylate-based sealant with improved elasticity ... Water soluble, lightfast, low odor, solvent and phthalate free. For filling joints and cracks inside and outside of premises on plaster, concrete, masonry, drywall, wood and chipboard, stone, absorbent ceramics, aluminum and corrosion-resistant metals. It is also especially suitable for joining the sealing joints of wooden and metal window frames, for shutters, internal and external window banks, aerated concrete, concrete and wooden elements, partitions. Not suitable for permanently wet loads. Consumption approx. 12.5 m2 for 5 mm x 5 mm connection Color white