LLC "Magnetpatch"

Fastening of the axle bridge (bridge-frame) to the emergency tank is carried out by means of two magnetic blocks М250, similar to used in the "Console" unit. The magnetic blocks are hingedly held together to the housing, inside of which the carriage moves along the guides with the sealing unit, which includes a press-screw and a rubber element.The set of delivery includes two types of sealing element: a cone and a gasket with diameters of 20 mm. Replacing one sealing element with another takes no more than 3 seconds.A cone is used to seal round gaps and holes, and a flat gasket is used for cracks or a group of small fistulas. Due to the movements of the carriage relative to the body and the sealing unit relative to the carriage, the sealing element is supplied directly to the leakage.The "aiming" zone is a 50x50 mm square surface. The surface to which the magnetic grippers will be attached is must be cleaned from dirt and coating.Product technical characteristics:Type - Bridge-frame (axle bridge) unitPressing force of the magnetic blocks to the metal surface - Not less than 2 * 250 kgfDiameter of the sealed tank (pipeline) - Not less than 400 mmThe maximum diameter of the sealed gap - At a pressure of 60 atm - not less than 7 mmInstallation time, min - 1-2Required number of workers - 1-2Dimensions, mm - 347x111x151Weight, kg - 5.4Service life - At the very least 10 years.

Monoblock unit М180, intended to exclude emergency leaks at relatively low pressures in emergency tanks.Between the magnetic blocks placed screw with a rubber sealing gasket. By applying a screw, the sealing gasket can be moved up or down relative to the unit.The monoblock unit is placed on the damaged container so that the leak will be under the rubber gasket. By rotating the handle, the plate with a rubber gasket is pressed on the defective place until the leak eliminates.The monoblock unit is removed by rotating the same handle in the same direction.Product technical characteristics:Type – Monoblock unitPressing force of the magnetic blocks to the metal surface - Not less than 150 kgfDiameter of the sealed tank (pipeline) - Not less than 400 mmMaximum diameter of the sealed gap - At a pressure of 5 atm - not less than 10 mmInstallation time, min - 0.5Required amount of workers - 1Dimensions, mm - 90x41x90Weight, kg - 0.8Service life - At the very least 10 years.

The K250 console is a permanent magnet device with controlled forceof the gravity. In the "off" condition, the console develops a force of attraction equal to 15-18 kgf. The presence of this force simplifies the installation of the console on the object: the console can be simply "sticked" to the damaged object. The sealing unit is installed on a carriage, which makes it possible to bring the sealing element directly on the leak. The carriage provides the ability to move the sealing unit in the longitudinal direction by a stroke of 15 mm, in the transverse direction - 20 mm and tilt the sealing unit in the longitudinal in the range of angles from 90 to 45 degrees. The set of delivery includes two types of sealing element: a cone and a 20 mm gasket. Replacing one sealing element with another takes just few seconds. A cone made for sealing round holes, and a flat gasket made for cracks or a group of small fistulas. The console is installed near the leak. The surface to which the magnetic block will be attached must be cleaned from dirt and coating. By rotating the handle, the magnetic block is "turned on". The sealing element need to bring to the hole to seal and the leak is can be eliminated by rotating the screw. Product technical characteristics: Type – Console unit Pressing force of the magnetic blocks to the metal surface - Not less than 250 kgf Diameter of the sealed tank (pipeline) - Not less than 400 mm Maximum diameter of the sealed gap - At a pressure of 25 atm - not less than 10 mm The range of inclination of the sealing unit in the longitudinal plane - From 90 to 45 degrees Installation time, min - 1-2 Required amount of workers - 1-2 Dimensions, mm - 275х121х151 Weight, kg - 3.4 Service life – At the very least 10 years.

The K200 console is intended to eliminate an emergency leak. The console is represents a magnetic block, which is also the hull of the unit. On the block with the help of a bracket fixed sealing unit, which includes a press-screw and a replaceable rubber sealing element. The set of delivery includes two types of sealing elements: a cone with a diameter of 12 mm and a flattened cone with a diameter of 12 mm and 5 mm. The mount allows you to replace one type of sealing element with another in few seconds. Fastening the press-screw to the bracket provides the ability to move the sealing unit in the transverse direction relative to the body by a stroke of ± 2 mm and tilt the sealing unit in the longitudinal plane in the range of angles 5 ° - 60 ° in vertical. Installation and removal of the K200 console carrying out by using a handle. A cone is used to seal round holes, in other cases a flattened cone. Product technical characteristics: Type – Console unit Pressing force of the magnetic blocks to the metal surface - Not less than 200 kgf Diameter of the sealed tank (pipeline) - From 80 to 100 mm Maximum diameter of the sealed gap - At a pressure of 25 atm - not less than 3 mm Installation time, min - 1 Required amount of workers - 1 Dimensions, mm - 149x96x61 Weight, kg - 0.9 Service life - At the very least 10 years.